Nkk Switches Toggle switch 250 Vac 10 A 2 x Off/On latch 1 pc(s) JWL21RAA/UC Scheda Tecnica

Indicators

Accessories

Supplement

Tactiles

Keylocks

Rotaries

Pushbuttons

Illuminated PB

Slides

Programmable

B

Rockers

Touch

Tilt

 

Toggles

General 

Specifications

  10A @ 125/250V AC for JWM & JWMW models; 10A @ 30V DC for JWMW;

 

  16A @ 125/250V AC for JWL & JWLW models; 5A @ 72V DC for telecommunication applications

Contact Resistance:   10 milliohms maximum for JWM & JWMW; 20 milliohms maximum for JWL & JWLW

Insulation Resistance:  1,000 megohms minimum @ 500V DC

Dielectric Strength:  2,000V AC minimum between contacts for 1 minute minimum; 

 

  4,000V AC minimum between contacts & case for 1 minute minimum

Mechanical Life:  25,000 operations minimum 

Electrical Life:  25,000 operations minimum 

Nominal Operating Force:  JWM & JWMW Single Pole 3.92N & Double Pole 7.84N

 

  JWL Single Pole 5.00N & Double Pole 10.00N;   JWLW Double Pole 10.00N 

Angle of Throw:    26° 

Rocker:  Polyphenylene ether (UL94V-0) 

Melamine (UL94V-0) 

 

Housing/Frame & Barrier:  Polyamide (UL94V-0) 

Contacts: 

Silver alloy with silver plating

  Interior Seal for JWM & JWL:  Polyphenylene sulfide (UL94V-0) 

Brass with silver plating

 Operating Temperature Range:  –25°C through +70°C (–13°F through +158°F) for JWM & JWL;
 

  –25°C through +85°C (–13°F through +185°F) for panel seal JWMW & JWLW models

Humidity:   90 ~ 95% humidity for 96 hours @ 40°C (104°F)

Vibration:  10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning  

 

  in 1 minute; 3 right angled directions for 2 hours

Shock:  50G (490m/s

2

) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)

Sealing:  IP67 of IEC60529 standard for panel seal JWMW & JWLW models; dust resistant inner seal for others

 Soldering Time & Temperature:   Manual Soldering:  See Profile A in Supplement section. 

Flammability Standards:  UL94V-0 for rocker, housing, seal & case/base of JWL, JWM,  JWMW & JWLW models

 

TV Ratings for UL & CSA:  JWM (TV-5) Overload Test  @ 120V AC for 50 operations:

 

   

Steady State Current (rms) 7.5A; Minimum Inrush Current  (peak) 111A.

 

  JWM (TV-5) Endurance Test  @ 120V AC for 25,000 operations:

 

   

Steady State Current (rms) 5A; Minimum Inrush Current  (peak) 78A.

 

  JWL (TV-8) Overload Test  @ 120V AC for 50 operations:

 

   

Steady State Current (rms) 12A; Minimum Inrush Current  (peak) 163A.

 

  JWL (TV-8) Endurance Test  @ 120V AC for 25,000 operations:

 

   

Steady State Current (rms) 8A; Minimum Inrush Current  (peak) 117A.

UL:  File No. E44145  

 

  JWM & JWMW models recognized at 10A @ 250V AC. 

 

  JWMW recognized at 10A @ 30V DC.

 

  JWL & JWLW models recognized at 16A @ 250V AC; JWL at 5A @ 72V DC.

 

  JWMW:  add “/U” to end of part number to order UL mark on switch;  add “/CUL”  to end of part 

 

  number to order cULus mark on switch.

 

  JWL:  add “/U-DC” to end of part number to request UL rating on DC rated switch.

CSA:  File No. 023535_0_000 

 

  JWM & JWMW models certified at 10A @ 250V AC;  JWL models certified at 16A @ 250V AC .

 

VDE:  License No. 115637 

 

  JWM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at  

  

  250V AC;  JWL models approved at steady state inrush 128A, resistive 16A, & motor load 8A  

 

  all at 250V AC.

 

  Note:  JWM & JWL Double Pole, Single Throw models approved only with the international  

 

  ON-OFF symbols on the actuator.