Texas Instruments Evaluation Module for TPS65708 TPS65708EVM-587 TPS65708EVM-587 Scheda Tecnica
Codici prodotto
TPS65708EVM-587
Connector and Test Point Descriptions
www.ti.com
4
Connector and Test Point Descriptions
4.1
Enable Jumpers/Switches (RefDes) TPS65708
4.1.1
J1 VLDO1
This header is the positive output of the LDO1 linear regulator. The default output voltage of the LDO is
2.8 V . The LDO is capable of sourcing up to 200 mA. A load can be connected between J1 and J3
(GND).
2.8 V . The LDO is capable of sourcing up to 200 mA. A load can be connected between J1 and J3
(GND).
4.1.2
J2 S+/S–
J2 S+/S– are the sense connection for the output of LDO1. Connect a voltmeter, sense connection of an
electronic load, or oscilloscope to this header.
electronic load, or oscilloscope to this header.
4.1.3
J3 GND
This header is the return connection for LDO1. A load can be connected between J3 (GND) and J1
(VLDO1). The LDO is capable of sourcing up to 200 mA.
(VLDO1). The LDO is capable of sourcing up to 200 mA.
4.1.4
J4 VINLDO1
This header is the input supply for LDO1 on the EVM. VINLDO1 is directly connected to VOUT_DCDC1
with R3 in the default EVM configuration. Alternatively, LDO1 can be supplied from VIN with resistor R1.
Use a 0-
with R3 in the default EVM configuration. Alternatively, LDO1 can be supplied from VIN with resistor R1.
Use a 0-
Ω
resistor for R1. Note that R3 must be removed if R1 is assembled.
An external power supply can be connected between J4 (VINLDO1) and J5 (GND). Note that resistors R1
and R3 must be removed when supplying LDO1 from an external power supply.
and R3 must be removed when supplying LDO1 from an external power supply.
4.1.5
J5 GND
J5 is the return connection of VINLDO1. An external power supply can be connected between J5 (GND)
and J4 (VINLDO1). Note that resistors R1 and R3 must be removed when supplying LDO1 from an
external power supply.
and J4 (VINLDO1). Note that resistors R1 and R3 must be removed when supplying LDO1 from an
external power supply.
4.1.6
J6 VINLDO2
J6 is the input supply for LDO2 on the EVM. VINLDO1 is directly connected to VOUT_DCDC2 with R4 in
tne default EVM configuration. Alternatively, LDO2 can be supplied from VIN with resistor R2. Use a 0-
tne default EVM configuration. Alternatively, LDO2 can be supplied from VIN with resistor R2. Use a 0-
Ω
resistor for R2. Note that R4 must be removed if R2 is assembled.
An external power supply can be connected between J6 (VINLDO2) and J7 (GND). Note that resistors R2
and R4 must be removed when supplying LDO2 from an external power supply.
and R4 must be removed when supplying LDO2 from an external power supply.
4.1.7
J7 GND
This jumper enables/disables the TPS65708 on the EVM. The shorting jumper JP1 between the center pin
and ON turns on the unit. Shorting the jumper between the center pin and OFF turns the unit off.
and ON turns on the unit. Shorting the jumper between the center pin and OFF turns the unit off.
4.1.8
J7 VOUT (SMA)
This header is the return connection of VINLDO2. An external power supply can be connected between J7
(GND) and J6 (VINLDO1). Note that resistors R2 and R4 must be removed when supplying LDO2 from an
external power supply.
(GND) and J6 (VINLDO1). Note that resistors R2 and R4 must be removed when supplying LDO2 from an
external power supply.
4.1.9
J8 VLDO2
J8 is the positive output of LDO2. The default output voltage of this LDO is 1.2 V. LDO2 is capable of
sourcing up to 200 mA. A load can be connected between J8 and J10 (GND).
sourcing up to 200 mA. A load can be connected between J8 and J10 (GND).
4
TPS65708EVM
SLVU402 – October 2010
Copyright © 2010, Texas Instruments Incorporated