Renkforce CU-4 USB-STUDIO-MIKROFON CU-4 Manuale Utente

•  Attach the shock mount on a suitable microphone holder with a 15.8 mm (5/8“) thread.
•  Squeeze the clips on the inner holder of the shock mount together and push the microphone into 

the holder. Release the clips to lodge the microphone in the shock mount.

•  Loosen the set screw on the shock mount to adjust the microphone to the desired angle. 
•  Then tighten the set screw by hand.
•  To remove the microphone from the shock mount, squeeze again the clips of the inner holder 

together and pull the microphone out of the holder.

•  Turn down the volume on the computer.
•  Connect the supplied USB cable to the microphone.
•  Connect the USB plug to a free USB port on your computer.
•  Wait until your operating system has recognised and installed the new hardware. This takes 

place automatically.

•  If necessary, set up the product as an audio resource on your computer.
•  Run the appropriate software for sound recordings.
•  Adjust the volume of the computer that has the microphone connected to it.
•  Unplug the product after use.

The studio microphone is maintenance-free.
Please use a soft, dry or slightly damp cloth for cleaning.
Never use aggressive cleaning agents or chemical solutions; this may damage the surface of the 

casing.

   Electronic devices are recyclable material and must not be disposed of in the house-

hold waste!

 

 Please dispose of the product, when it is no longer of use, according to the current 

statutory requirements.

System requirements ..................................Windows

®

 2000 and later

Connection ....................................................USB 2.0
Sample rate ...................................................16 Bit
Current consumption  ..................................2 mA
Impedance ....................................................200 Ohm
Frequency range ..........................................20-20000 Hz
Sensitivity ......................................................-36 ±2 dB (0 dB = 1 V/Pa at 1 kHz)
Max. input level SPL ....................................140 dB (1 kHz at 1% THD)
Directional pattern .......................................Cardioid
Membrane .....................................................25 mm (1“) Gold diaphragm
Working principle .........................................Condenser microphone
Dimensions (Ø x H).......................................51 x 184 mm
Weight ............................................................445 g

G   Operating instructions

The studio microphone is intended to convert acoustic signals (sound waves) into electrical sig-

nals. It supports podcasting, multimedia presentations, and other applications such as audio re-

cordings.
The USB port may only be connected to appropriate USB ports of computers.
Any use other than as described above is not permitted and can damage the product. In addition, 

it can lead to hazards such as short-circuit, fire, etc.
Read the operating instructions carefully and keep them for later reference. If you pass the product 

on to a third party, please hand over these operating instructions as well.
No part of the product may be modified or converted.
The safety instructions must be observed at all times.
This product complies with the applicable national and European requirements. All names of com-

panies and products are the trademarks of the respective owners. All rights reserved.

•  Microphone
•  USB cable (3 m)
•  Shock mount
•  Case
•  Operating instructions

 

•   For safety reasons, any unauthorised conversion and/or modification to the product 

are not permitted.

 

•   When connecting the microphone, pay attention to the safety instructions of the de-

vice to which it is to be connected.

 

•   Do not expose the product to high temperatures, strong vibrations, dripping water or 

water spray.

 

•  Use the product only in a temperate climate, never in a tropical climate.

 

•  This product is not a toy and should be kept out of reach of children.

 

•   Don’t leave packaging material lying around carelessly; it may become a dangerous 

plaything for children.

 

•   Handle the product with care; it can be damaged by impact, blows, or accidental 

drops, even from a low height.

 

•   Also observe any further safety instructions in the individual chapters of these oper-

ating instructions.

 

•   In commercial institutions, the accident prevention regulations of the Employer’s Li-

ability Insurance Association for Electrical Systems and Operating Facilities are to 

be observed.

 

•   If you are unsure how to connect the product properly, or should you have any ques-

tions that are not answered in these operating instructions, please contact our tech-

nical service or consult a professional.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). 
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data 

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent 

the technical status at the time of printing.  
© Copyright 2014 by Conrad Electronic SE.