Renkforce Decorative Lighting 5MAC532W 5MAC532W Scheda Tecnica

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). 
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data 

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent 

the technical status at the time of printing.  
© Copyright 2014 by Conrad Electronic SE. 

   Before you start the installation, keep in mind that the IR receiver of the con-

trol unit must be placed so that a flawless reception of the control signals of 

the IR remote control is possible.

 

 A direct optical contact between the IR LED of the IR remote control and the 

IR receiver is beneficial, however it is not a prerequisite. The IR light (invis-

ible to the human eye) of the IR remote control is reflected by many surfaces. 

 

 Before you proceed to the permanent mounting of the control unit and the IR 

receiver, check that they function properly. 

•  The control unit can be screwed down via two straps located on the side of the 

housing. Depending on the mounting site, you can also fasten the control unit using 

cable ties or a double-sided adhesive tape.

   When you fasten the control unit, pay attention when drilling and tightening 

the screws that no cables or pipes are damaged.

•  Fasten the IR receiver of the control unit to a suitable place, e.g. by using a strip of 

adhesive tape or a cable tie.

•  The  LED  strip  can  be  mounted  on  suitable  surfaces,  such  as  furniture  or  similar 

objects, using the adhesive tape located on the bottom side. 

   The LED strip must be mounted in such a way that it is not exposed to me-

chanical stress. The strip must be mounted so that no one can step on it, 

otherwise it will be damaged. 

•  Carefully clean the surface onto which you want to mount the LED strip from dust, 

dirt  and  grease  before  sticking  it,  otherwise  the  adhesive  tape  will  come  off  the 

surface.

•  Then slightly remove the protective strip and stick the LED strip bit by bit onto the 

mounting surface. However, do not use force when pressing down.

   The LED strip can be cut off at the indicated points. The individual LED strip 

parts can be electrically reconnected using the connectors provided. 

•  Connect the 4-pole connector of the LED strip to the respective 4-pole socket of the 

control unit using one of the plug-in connectors enclosed. 

   Make sure the labellings of the connectors match (labelling “+ - - +” on the 

socket of the control unit should point at the labelling “+ - - +” of the LED 

strip).

•  The plug connection can be protected from unintentional disconnection by using a 

strip of adhesive tape.

•  Connect the round low voltage plug of the power adapter to the appropriate round 

socket on the control unit.

•  Connect the power adapter to a proper mains socket of the public power grid.

•  Open the battery compartment on the back of the IR remote control and insert two 

batteries of type “CR2023”, while paying attention to the correct polarity (plus/+ and 

minus/-). Close the battery compartment again.

•  The batteries need replacing if the range of the IR remote control decreases or the 

control unit no longer responds to the IR remote control.

Point the LED on the front of the IR remote control at the IR receiver of the control unit 

and press the corresponding key.
“ON” 

key to switch the LED strip on

“OFF” 

key to switch the LED strip off

“CW” 

key for selection of the light colour “cold-white”

“CW” 

key for selection of the light colour “warm-white”

“*” 

key to reduce the brightness

Key “

*

” 

to increase the brightness

The light colour can be set to “cold-white” and “warm-white” as desired, using the 

large circular surface on the IR remote control.

•  Apart from the occasional replacement of the batteries in the IR remote control, the 

product is maintenance-free. 

  The integrated LED bulbs are permanently installed and they cannot be replaced.
•  Before carrying out any cleaning, the product is to be disconnected from the mains 

voltage. Pull the power adapter out of the mains socket.

•  The outside of the product should only be cleaned with a clean, soft, dry cloth. 

   Do  not  use  aggressive  cleaning  agents  or  chemical  solutions  that  could 

damage the housing (discolouring) or impair operation. 

 Dispose of an unserviceable product in accordance with the relevant statu-

tory regulations.

 

 Remove  any  inserted  batteries  and  dispose  of  them  separately  from  the 

product.

As the end user, you are required by law (Battery Ordinance) to return all used bat-

teries/rechargeable batteries; disposal of them in the household waste is prohibited.

   Contaminated batteries/rechargeable batteries are labelled with these sym-

bols to indicate that disposal in the domestic waste is forbidden. The desig-

nations for the heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb 

= Lead.

Used batteries, rechargeable batteries as well as coin cells can be returned to collec-

tion points in your municipality, our stores or wherever batteries/rechargeable batter-

ies/coin cells are sold.
You therefore fulfil your statutory obligations and contribute to the protection of the 

environment.

Total power input ............................... 24 W
Ambient conditions ............................  Temperature 0 °C to +40 °C, 

 ......................................

Humidity 5% to 80% relative air humidity, non-con-

densing

Length .................................................. 5 m
Cross-section...................................... (W x H) 10 x 2.9 mm
Number of LEDs.................................. 150 x cold-white, 150 x warm-white
Weight .................................................. approx. 630 g

Operating voltage............................... 100 - 240 V/AC, 50/60 Hz
Output................................................... 12 V/DC, 2 A

Operating voltage............................... 12 V/DC
Required current ................................ 2 A
Dimensions.......................................... 35 x 50 x 22.5 mm (W x L x H)
Weight .................................................. 37 g

Power supply ...................................... 2x batteries of type CR2023
Dimensions.......................................... 52 x 85 x 7 mm (W x H x D)
Weight .................................................. 30 g (incl. batteries)