Renkforce Decorative Lighting LED strip, digital colour change, 5 m 5MCC316W LED 5MCC316W Scheda Tecnica

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). 
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data 

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent 

the technical status at the time of printing.  
© Copyright 2014 by Conrad Electronic SE. 

•  Open the battery compartment on the back of the IR remote control and insert a battery of type 

“CR2025”, paying attention to the correct polarity (pay attention to plus/+ and minus/-). Close the 

battery compartment again.

•  The battery needs replacing if the range of the IR remote control decreases or if the control unit 

no longer responds to the remote control.

Point the LED on the front of the IR remote control at the IR receiver of the control unit and press 

the corresponding button.

  Switching the LED strips on/off

  Toggling between light colour warm white/cold white

  Playing all light programmes automatically one after another

   Increasing the speed (of a running light programme) or increasing the brightness (if a static 

colour is displayed)

   Decreasing the speed (of a running light programme) or decreasing the brightness (if a 

static colour is displayed)

   Selecting of an individual colour (red, green, blue, yellow, purple, cyan blue, cold white, 

warm white) which the light programme is to use later

   The subsequently selected light programme uses 3 colours (red + green + blue)

   The subsequently selected light programme uses 7 colours (red + green + blue + yellow + 

purple + white)

   The subsequently selected light programme uses 16 colours (red + green + blue + yellow + 

purple + cyan blue + white + orange + dark yellow + light yellow + light green + light blue + 

azure + purple + magenta)

  Deactivating of parts of the LED strip  (see next chapter)

   Light programme “Opening the curtain” (LEDs are dimmed in the middle of the LED strip, the 

dimmed area runs from the middle to the outer edges)

   Light programme “Closing the curtain” (the selected colour starts at the ends of the LED 

strip and runs towards the middle)

   Light  programme  “Trailing  to  the  left”  (similar  to  a  running  light;  the  unused  LEDs  are 

dimmed)

   Light  programme  “Trailing  to  the  right)  (similar  to  a  running  light;  the  unused  LEDs  are 

dimmed)

   Light  programme  “selected  colour  runs  to  the  left”  (the  unused  LEDs  are  illuminated  in 

white)

   Light  programme  “selected  colour  runs  to  the  left”  (the  unused  LEDs  are  illuminated  in 

white)

  Light programme “Stars running to the right” (waterfall effect)

  Light programme “Stars running to the left” (waterfall effect)

  Light programme “Running light to the left”

  Light programme “Running light to the right”

   Light programme “Rainbow” (running light with the selected colour(s) running alternately 

to the left and right)

  Light programme “Blinking” (all LEDs are dimmed/lit)

  Light programme “Jumping” (all LEDs are switched on/off)

   Light programme “Meteor tail” (waterfall effect with the selected colour(s) running alter-

nately to the left and right)

Due to the digital control of the LED strip, you can deactivate parts of the LED strip. For example, 

if you only need 4 m of the LED strip, you do not need to cut it off but you can switch off the 1 m 

section of the LED strip you do not require.
Proceed as follows:
•  Switch on the LED strip.
•  Press the 

 button (IC set); the programming mode is now activated. The LEDs are lit in white.

•  Use the arrow button 

 to deactivate the LEDs at the end of the LED strip (always in groups of 

three); press the button several times, if necessary.

  Use the 

 button to activate the LEDs again.

•  Press the 

 button (IC set) to leave the programming mode.

•  Apart from the the occasional battery change for the IR remote control, the product is mainte-

nance-free. 

  The built-in LED bulbs are permanently installed; they cannot be replaced.
•  Before carrying out any cleaning, the product is to be separated from the mains voltage, pull the 

wall plug transformer from the mains socket.

•  The outside of the product should only be cleaned with a clean, soft, dry cloth. 

   Do not use aggressive cleaning agents or chemical solutions that could damage the 

housing (discolouring) or impair operation. 

  Dispose of an unserviceable product in accordance with the relevant statutory regula-

tions.

 

 Remove any battery in the IR remote control and dispose of it separately from the product.

As the end user, you are required by law (Battery Ordinance) to return all used batteries/recharge-

able batteries; disposal of them in the household waste is prohibited.

   Contaminated batteries/rechargeable batteries are labelled with these symbols to in-

dicate that disposal in the domestic waste is forbidden. The designations for the heavy 

metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead.

Used batteries, rechargeable batteries as well as coin cells can be returned to collection points 

in your municipality, our stores or wherever batteries/rechargeable batteries/coin cells are sold.
You therefore fulfil your statutory obligations and contribute to the protection of the environment.

Total power consumption ...........................24 W
Operating conditions ................................... Temperature 0 °C to +40 °C, 

 ...................................................

Humidity 5% to 80% relative air humidity, non-condensing

Length ............................................................5 m
Cross-section (W x H) .................................10 x 3.1 mm
Number of LEDs............................................150 x RGB
Weight ............................................................approx. 650 g

Operating voltage.........................................100 - 240 V/AC, 50/60 Hz
Output.............................................................12 V/DC, 3 A

Operating voltage.........................................12 V/DC
Required current ..........................................min. 3 A
Dimensions....................................................35 x 50 x 22.5 mm (W x L x H)
Weight ............................................................37 g

Power supply ................................................1x battery of type CR2025
Dimensions....................................................52 x 85 x 7 mm (W x H x D)
Weight ............................................................35 g (incl. battery)