MEAN WELL CLG-100-24 Scheda Tecnica

I/P-O/P:3.75KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC

I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH

IP67

..

12V

9 ~ 12V

15V

11.25 ~ 15V

20V

15 ~ 20V

24V

18 ~ 24V

27V

20.25 ~ 27V

36V

27 ~ 36V

48V

36 ~ 48V

5A

5A

4.8A

4A

3.55A

2.65A

2A

60W

75W

96W

96W

95.85W

95.4W

96W

150mVp-p

150mVp-p

150mVp-p

150mVp-p

150mVp-p

150mVp-p

200mVp-p

±3.0%

±3.0%

±3.0%

±3.0%

±3.0%

±2.0%

±2.0%

Fixed. Can be modified between 0% ~ -15% rated output voltage

Fixed. Can be modified between 3% ~ -25% rated output current

±1.0%

±2.0%

500ms, 80ms / 230VAC          

 at full load

1200ms, 80ms / 115VAC

60ms / 230VAC          30

 at full load

ms / 115VAC

90 ~ 295VAC          127 ~ 417VDC

47 ~ 63Hz

PF>0.95/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

13 ~ 16V

16.5 ~ 20V

22 ~ 27V

27 ~ 34V

30 ~ 36V

39 ~ 48V

52 ~ 64V

COLD START 40A(twidth=1030 s measured at 50% Ipeak) at 230VAC

μ

<0.75mA / 240VAC

95 ~ 102%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV),  criteria A

-30 ~ +70

 

℃ (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +80

, 10 ~ 95% RH

℃

±

℃

℃

0.03%/

 (0 ~ 50

)

10 ~ 500Hz, 5G 12min./1cycle, period for  72min. each along X, Y, Z axes

301Khrs min.      MIL-HDBK-217F (25

)

℃

222.2*68*38.8mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltages. Please check the static characteristics for more details.

5. This is the maximum possible output current and power, over load protection may be activated slightly below this level to comply with the requirement 

    of UL1310 class 2.
6. 3 years warranty is guaranteed for operating ambient temperature no higher than 68℃.

8. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.

9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the 

    complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Please refer to "DRIVING METHODS OF LED MODULE".

10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently 

      connected to the mains.

1.0Kg; 12pcs/13Kg/0.58CUFT

Protection type : Shut down and latch off o/p voltage, re-power on to recover

100W Single Output Switching Power Supply

‧

Universal AC input / Full range (up to 295VAC)

‧

Built-in active PFC function

‧

‧

Protections: Short circuit / Over current / Over voltage / Over temperature 

‧

Cooling by free air convection

‧

IP67 design for indoor or outdoor installations

‧

Class 2 power unit

‧

Pass LPS

‧

100% full load burn-in test

‧

High reliability

‧

Suitable for LED lighting and moving sign applications

‧

Compliance to worldwide safety regulations for lighting 

‧

Suitable for dry / damp / wet locations

‧

3 years warranty (Note.6)

High efficiency up to 88.5%

■

 Features :

Shut down o/p voltage, re-power on to recover

( for 48V only)

( except for 48V )

Hiccup mode, recovers automatically after fault condition is removed

Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (≧75% load) ; EN61000-3-3

83%

85%

88.5%

88.5%

88%

88%

88.5%

12V:0.8A/115VAC     0.4A/230VAC

          

    0.3A/277VAC

15V:0.9A/115VAC     0.45A/230VAC    0.35A/277VAC

20V ~ 48V:1.1A/115VAC     0.55A/230VAC     0.45A/277VAC

CSA C22.2 No. 250.0-08(except for 48V), CSA C22.2 No. 207-M89(except for 48V), TUV EN60950-1, IP67, J61347-1, J61347-2-13  approved

UL879, UL8750, UL1310, TUV EN61347-1, EN61347-2-13 independent, CAN/CSA C22.2 No. 223-M91(except for 48V),