Mueller electrical installation 873030 Dépliant
Codici prodotto
873030
BA 873030led N;DE,GB -23249- 2014.06-V04
INSTRUCTION MANUAL DIMMER [LED]
Technical Features
Safetey instructions
Supply voltage
230 V, 50Hz
CAUTION!! DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption
2 VA
Suitable type of lamps
Dimmable LED lamps
LOA
D
LED 1: Dimmable 230V~ LED lamps* (leading edge dimming) 4 - 100 W
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately!
Warranty void if housing opened by unauthorised person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes!
LED 2: Dimmable 230V~ LED lamps* (trailing edge dimming). 4 - 100 W
LED 2: Dimmable 12V~ LED lamps* (trailing edge dimming)
LED 2: Dimmable 12V~ LED lamps* (trailing edge dimming)
with Electronic transformer, type C
1 lamp per transformer /
max. 6 transformers (50W)
Max. number of pushbuttons
3 lighted pushbuttons & unlimited
non-lighted pushbuttons
Dimensions
45 x 45 x 12 mm
Weight
23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection
IP20 according to DIN EN 60529
Important Note
Conformity with Standard
DIN EN 60669-2-1
For all transformers and lamps, please take into account the specifications of the manufacturer!
*Check the technical specification of the lamps.
Description / Installation / Operation
Wiring diagram
Wiring example
Description
Small size dimmer, for flush-mounting (e.g. behind standard pushbutton)
Protected against overload and short circuit. Built-in heat protection.
Controlled by pushbutton.
With or without memory.
One rotary switch to select the minimum light level and to select the connected lamp load (LED1 or LED2).
- LED 1: Dimmable 230V~ LED lamps* (leading edge dimming)
- LED 2: Dimmable 230V~ LED lamps* (trailing edge dimming).
Dimmable 12V~ LED lamps* (trailing edge dimming) with Electronic transformer, type C
For all transformers and lamps, please take into account the specifications of the manufacturer!
Installation
CAUTION! You must select with the rotary switch (LED1 or LED2) the correct type of connected load in order
to avoid damages of the dimmer or the lamps!
PLEASE NOTE! To avoid undesirable effects when the lamps are dimmed to lowest level (e.g. light flickering)
you have to select with the rotary switch the minimum light level!
1 Disconnect installation from power supply and check that power supply is disconnected.
2 Select with the rotary switch the type of lamp / load you will connect (LED1 or LED2).
3 Install the dimmer according to the wiring diagram.
4 Make sure the loads are connected properly and reconnect power supply.
5 Press shortly the pushbutton to switch the lamps on and dim with a long press to the minimum lighting level.
If the lamps are not switched on correct (e.g. light flickering) please select with the rotary switch the appropriate
and correct minimum light level.
Operation
Press shortly the pushbutton to switch the lamps on and off!
=> Switch on „No Mem“ = Lamp(s) switches on with max. brightness.
=> Switch on „Mem“ = Lamp(s) switches on with the brightness of the last switch off
With a long press you can dim!
Example:
Quick and easy! One rotary switch to set
the lamp load and the minimum light level
Setting the lamp load
Check the technical
specification of the lamps.
Setting the minimum
light level
/ dimming value