Graupner Pistol grip RC 2.4 GHz No. of channels: 3 94004 Manuale Utente

23                                           94004 GM-Racing XG-6i 2.0 FHSS Race Spec

English

The  basic  rule  is  that  all  linkages  should  be  installed  in  such  a  way  that  the  pushrods  move 

The basic rule is that all linkages should be installed in such a way that the pushrods move 

• 

• 

accurately, smoothly and freely. It is particularly important that all servo output arms can move 

accurately, smoothly and freely. It is particularly important that all servo output arms can move 

to their full extent without fouling or rubbing on anything, or being obstructed mechanically at 

to their full extent without fouling or rubbing on anything, or being obstructed mechanically at 

any point in their travel.

any point in their travel.

It is important that you can stop your motor at any time. With a glow motor this is achieved by 

It is important that you can stop your motor at any time. With a glow motor this is achieved by 

• 

• 

adjusting the throttle so that the barrel closes completely when you move the throttle stick and 

adjusting the throttle so that the barrel closes completely when you move the throttle stick and 

trim to their end-points.

trim to their end-points.

Ensure that no metal parts are able to rub against each other, e. g. when controls are operated, 

Ensure that no metal parts are able to rub against each other, e. g. when controls are operated, 

• 

• 

when parts rotate, or when motor vibration affects the model.

when parts rotate, or when motor vibration affects the model.

Metal-to-metal contact causes electrical “noise” which can interfere with the correct working of 

Metal-to-metal contact causes electrical “noise” which can interfere with the correct working of 

• 

• 

the receiver.

the receiver.

Never  fl y  directly  over  spectators  or  other  pilots,  and  take  care  at  all  times  not  to  endanger 

Never  fl y directly over spectators or other pilots, and take care at all times not to endanger 

• 

• 

people or animals. 

people or animals. 

Never run your model boat close to locks and fullsize boats. Model cars should never be run on 

Never run your model boat close to locks and fullsize boats. Model cars should never be run on 

• 

• 

public streets or motorways, footpaths, public squares etc..

public streets or motorways, footpaths, public squares etc..

It is essential to stop using the radio control system and recharge the batteries well before they 

It is essential to stop using the radio control system and recharge the batteries well before they 

• 

• 

are completely discharged. 

are completely discharged. 

It  is  vital  to  check  the  state  of  the  receiver  battery  at  regular  intervals.  When  the  battery  is 

It is vital to check the state of the receiver battery at regular intervals. When the battery is 

• 

• 

almost fl at you may notice the servos running more slowly, but it is by no means safe to keep 

almost fl at you may notice the servos running more slowly, but it is by no means safe to keep 

fl ying or running your model until this happens. Always replace or recharge the batteries in good 

fl ying or running your model until this happens. Always replace or recharge the batteries in good 

time.

time.

Keep to the battery manufacturer’s instructions and don’t leave the batteries on charge for a 

Keep to the battery manufacturer’s instructions and don’t leave the batteries on charge for a 

• 

• 

longer period than stated. Do not leave batteries on charge unsupervised.

longer period than stated. Do not leave batteries on charge unsupervised.

Never attempt to recharge dry cells, as they may explode.

Never attempt to recharge dry cells, as they may explode.

• 

• 

Rechargeable batteries should always be recharged before every session. When charging batte-

Rechargeable batteries should always be recharged before every session. When charging batte-

• 

• 

ries it is important to avoid short-circuits. Do this by connecting the charge lead banana plugs to 

ries it is important to avoid short-circuits. Do this by connecting the charge lead banana plugs to 
the charger fi rst, taking care to maintain correct polarity. Only then connect the 

the charger fi rst, taking care to maintain correct polarity. Only then connect the 

charge lead to 

charge lead to 

the transmitter or receiver battery.

the transmitter or receiver battery.

Disconnect all batteries and remove them from your model if you know you will not be using it 

Disconnect all batteries and remove them from your model if you know you will not be using it 

• 

• 

in the near future.

in the near future.

This rule applies to all forms of electrical power source: capacity is greatly reduced at low tem-

This rule applies to all forms of electrical power source: capacity is greatly reduced at low tem-

• 

• 

peratures, i. e. operating times are shorter in cold conditions. 

peratures, i. e. operating times are shorter in cold conditions. 

Frequent charging of batteries, and use of battery maintenance programs, can also result in a 

Frequent charging of batteries, and use of battery maintenance programs, can also result in a 

• 

• 

landing shocks will be transmitted directly to it.

landing shocks will be transmitted directly to it.

When installing the receiving system in a model powered by a glowplug or petrol engine, be sure 

When installing the receiving system in a model powered by a glowplug or petrol engine, be sure 

• 

• 

to install all the components in well-protected positions so that no exhaust gas or oil residues 

to install all the components in well-protected positions so that no exhaust gas or oil residues 

can reach the units and get inside them. 

can reach the units and get inside them. 

Secure the receiver in such a way that the aerial, servo leads and switch harness are not under 

Secure the receiver in such a way that the aerial, servo leads and switch harness are not under 

• 

• 

any strain.

any strain.

Do not bend or shorten the receiver aerial! 

Do not bend or shorten the receiver aerial! 

• 

• 

Always  install  servos  using  the  vibration-damping  grommets  supplied.  The  rubber  grommets 

Always install servos using the vibration-damping grommets supplied. The rubber grommets 

• 

• 

provide some degree of protection from mechanical shocks and severe vibration.

provide some degree of protection from mechanical shocks and severe vibration.