Rocketfish QS2-T Dépliant

Indicator

Volume down
Power/Send/End
button

Microphone

Volume up

Visor clip

Charger 

connector

Congratulations on your purchase of the RF-QS2-T 
Bluetooth Speakerphone. This speakerphone enables 
comfortable, hands-free communication with a 
Bluetooth-compatible phone.

•  RF-QS2-T speakerphone 

•  Car charger adapter

 

•  USB charging cable 

•  Quick Setup Guide

Charging the battery
Before using your speakerphone, you must charge it 
for about two hours. When the battery is fully charged, 
it provides up to 11 hours of talk time and up to 
1,400 hours of standby time.
1  USB charging: use the USB cable to plug your QS2-T 

speakerphone into a computer or other USB power 
port.

2  Car charging: use the car charger adapter and USB 

charging cable to charge your QS2-T speakerphone 
in your car.

Turning the speakerphone on 
Press and hold the Power/Send/End for about 
two seconds. RF-QS2-T beeps and the yellow-green 
indicator light starts blinking. (First time use requires 
pressing it for 4 seconds.) 

Turning the speakerphone off
Press and hold the Power/Send/End for about 
four seconds, RF-QS2-T beeps and the red indicator light 
is displayed briefly. 

Pairing the speakerphone
1  Make sure that the compatible phone is turned on 

and within 33 ft. (10 m) of the speakerphone.

2  Turn on the QS2-T and make sure it’s fully charged. 

Press and hold the Power/Send/End button for 
about four seconds. The yellow-green indicator 
flashes rapidly. Release the button. The 
speakerphone is now in pairing mode.

3  Activate the Bluetooth connection from the phone. 

See your phone’s documentation for more 
information.

4  Set the phone to start searching for Bluetooth 

devices.

5 Select 

 from the list.

6 Enter 

the 

PIN 

0000 to connect (or “pair”) the 

speakerphone to the phone. The speakerphone 
beeps once, and the indicator blinks yellow-green to 
indicate the Bluetooth connection is active.

Make a call 

Press Power/Send/End.

Redial Double-press 

Power/Send/End.

Answer a call 

Press Power/Send/End.

End a call 

Press Power/Send/End.

Refuse a call 

Double-press Power/Send/End.

Change the speaker 

Press the volume up button (+) to increase 

volume 

volume or press the volume down (-) button to 

 decrease.

Mute or unmute a call 

Press and hold the Volume down (-) button until 

 

a tone is heard.

Switch a call between  

Press and hold Power/Send/End for 

the phone and the  

two seconds.

speakerphone

Voice dialing
When no call is in progress, quickly press and release 
Power/Send/End. When you hear a tone, speak the 
number or voice tag for the number you want to call. 
(The phone must have a voice dial feature and have 
recorded voice tags.) 

Turning the indicator on or off
• 

Press the power and volume up buttons at the same 
time for about four seconds. The indicator turns on. 
Press the power and volume down buttons at the 
same time for about four seconds. The indicator 
turns off. You can enable or disable the indicator 
when the speakerphone is connected with your 
phone.

Disconnecting the speakerphone from the phone
To disconnect the speakerphone from the phone, do 
one of the following:
• 

Turn off the speakerphone.

• 

Disconnect the RF-QS2-T in the phone’s menu.

• 

Move the speakerphone more than 33 ft. (10 m) 
away from the phone.

Note: You do not need to delete the pairing to 
disconnect the speakerphone. When you reconnect a 
paired speakerphone, you will not be asked for its PIN 
again.
If you want to pair your speakerphone with new phones, 
you don’t need to erase all paired device information. 
There can be up to eight different paired devices 
information stored.

To erase paired devices from your speakerphone:
• 

When the speakerphone turned off, press and hold 
the Power/Send/End and volume up (+) buttons 
simultaneously for more than six seconds. A tone 
plays, and the indicator flashes red and yellow-green. 
The speakerphone then enters the pairing state 
automatically.