Texas TMS320C645X Manuale Utente
www.ti.com
2
SRIO Functional Description
2.1
Overview
SRIO Functional Description
2.1.1
Peripheral Data Flow
This peripheral is designed to be an external slave module that is capable of mastering the internal DMA.
This means that an external device can push (burst write) data to the DSP as needed, without having to
generate an interrupt to the CPU. This has two benefits. It cuts down on the total number of interrupts, and
it reduces handshaking (latency) associated with read-only peripherals.
This means that an external device can push (burst write) data to the DSP as needed, without having to
generate an interrupt to the CPU. This has two benefits. It cuts down on the total number of interrupts, and
it reduces handshaking (latency) associated with read-only peripherals.
SRIO specifies data packets with payloads up to 256 bytes. Many times, transactions will span across
multiple packets. RapidIO specifies a maximum of 16 transactions per message. Although a request is
generated for each packet transaction so that the DMA can transfer the data to L2 memory, an interrupt is
only generated after the final packet of the message. This interrupt notifies the CPU that data is available
in L2 Memory for processing.
multiple packets. RapidIO specifies a maximum of 16 transactions per message. Although a request is
generated for each packet transaction so that the DMA can transfer the data to L2 memory, an interrupt is
only generated after the final packet of the message. This interrupt notifies the CPU that data is available
in L2 Memory for processing.
As an endpoint device, the peripheral accepts packets based on the destination ID. Two options exist for
packet acceptance and are mode selectable. The first option is to only accept packets whose DestIDs
match the local deviceID in 0x0080. This provides a level of security. The second option is to accept
incoming packets matching the deviceID in either 0x0080 or 0x0084. This allows for system multicast
operations.
packet acceptance and are mode selectable. The first option is to only accept packets whose DestIDs
match the local deviceID in 0x0080. This provides a level of security. The second option is to accept
incoming packets matching the deviceID in either 0x0080 or 0x0084. This allows for system multicast
operations.
Data flow through the peripheral can be explained using the high-level block diagram shown in
.
High-speed data enters from the device pins into the RX block of the SERDES macro. The RX block is a
differential receiver expecting a minimum of 175mV peak-to-peak differential input voltage (Vid). Level
shifting is performed in the RX block, such that the output is single ended CMOS. The serial data is then
fed to the SERDES clock recovery block. The sole purpose of this block is to extract a clock signal from
the data stream. To do this, a low-frequency reference clock is required, 1/10
differential receiver expecting a minimum of 175mV peak-to-peak differential input voltage (Vid). Level
shifting is performed in the RX block, such that the output is single ended CMOS. The serial data is then
fed to the SERDES clock recovery block. The sole purpose of this block is to extract a clock signal from
the data stream. To do this, a low-frequency reference clock is required, 1/10
th
or ½0
th
the data rate. For
example, for 3.125 Gbps data, a reference clock of 312.5Mhz or 156.25Mhz is needed. Typically, this
clock comes from an off-chip stable crystal oscillator and is a LVDS device input separate to the SERDES.
This clock is distributed to the SERDES PLL block which multiplies that frequency up to that of the data
rate. Eight phases of this high-speed clock are created and routed to the clock recovery blocks. The clock
recovery block further interpolates eight times between these clock phases. This provides clock edge
resolution of 1/96
clock comes from an off-chip stable crystal oscillator and is a LVDS device input separate to the SERDES.
This clock is distributed to the SERDES PLL block which multiplies that frequency up to that of the data
rate. Eight phases of this high-speed clock are created and routed to the clock recovery blocks. The clock
recovery block further interpolates eight times between these clock phases. This provides clock edge
resolution of 1/96
th
the Unit Interval (UI). The clock recovery block samples the incoming data and
monitors the relative positions of the data edges. With this information, it can provide the data and a
center-aligned clock to the S2P block. The S2P block uses the newly recovered clock to demux the data
into 10-bit words. At this point, the data leaves the SERDES macro at 1/10th the pin data rate,
accompanied by an aligned byte clock.
center-aligned clock to the S2P block. The S2P block uses the newly recovered clock to demux the data
into 10-bit words. At this point, the data leaves the SERDES macro at 1/10th the pin data rate,
accompanied by an aligned byte clock.
SPRU976 – March 2006
Serial RapidIO (SRIO)
19