GSI Outdoors 100 SERIES DRYER PNEG-552 Manuale Utente
6. Dryer Start-Up
PNEG-552 100 Series Dryer
29
10. After purging for approximately 10 seconds the heater will fire. For information concerning heater
adjustment, see
11. If the dryer is being operated in all heat, move the FAN switch to the ON position. In this position,
the fan will run continuously during the dry, cool and unload stages of the staged batch operation.
If the dryer is being operated in the dry and cool mode, the preferred position for the FAN switch is
the ON position, so the fan will run continuously and continue to cool the grain during the unload
operation. If desired, the fan can be turned OFF during the unload cycle of the dry-cool-unload
sequence by turning the FAN switch to AUTO.
If the dryer is being operated in the dry and cool mode, the preferred position for the FAN switch is
the ON position, so the fan will run continuously and continue to cool the grain during the unload
operation. If desired, the fan can be turned OFF during the unload cycle of the dry-cool-unload
sequence by turning the FAN switch to AUTO.
12. If the dryer is being operated in all heat, move the HEATER switch to ON. The burner will operate
whenever the fan is operating. If the dryer is being used in dry and cool, turn the HEATER switch
to AUTO and the burner will automatically shut down during the cooling and unloading cycles.
to AUTO and the burner will automatically shut down during the cooling and unloading cycles.
13. The bottom auger and metering rolls will start automatically during the unload cycle of the
dry-cool-unload mode, along with any grain handling equipment that is wired to the dryer. The
speed at which the metering rolls operate during the unload cycle is adjusted by using the high
speed metering roll knob. Turning the dial clockwise will increase the grain discharge rate, and
turning it counterclockwise will decrease the discharge rate.
speed at which the metering rolls operate during the unload cycle is adjusted by using the high
speed metering roll knob. Turning the dial clockwise will increase the grain discharge rate, and
turning it counterclockwise will decrease the discharge rate.
14. When the last batch is done and the dryer is out of grain, turn the drying mode switch to continuous.
Turn the load, unload, fan/heater switches off and push the dryer power start switch to arm the
safety circuit. Run the fan/heater manually for 6 minutes per point of moisture to be removed.
Turn the burner off to cool the grain for 30 minutes. Turn off the fan and manually unload the dryer
by turning the unload switch to 1 Speed and setting the meter rolls as fast as the unload equipment
will allow.
safety circuit. Run the fan/heater manually for 6 minutes per point of moisture to be removed.
Turn the burner off to cool the grain for 30 minutes. Turn off the fan and manually unload the dryer
by turning the unload switch to 1 Speed and setting the meter rolls as fast as the unload equipment
will allow.
15. To control the length of the dry cycle using only the dry time setting programmed into the system,
turn the MOISTURE CONTROL setting to OFF. To use the automatic moisture control so that the
dry time is determined, not only by the dry time setting, but also by the moisture content of the
drying grain, turn the MOISTURE CONTROL switch to ON.
dry time is determined, not only by the dry time setting, but also by the moisture content of the
drying grain, turn the MOISTURE CONTROL switch to ON.
16. To shut down the dryer, close the fuel supply valve at the fuel tank or fuel source. If the burner is
operating, let the dryer run out of fuel, causing an automatic shut down due to a loss of flame. Close
the fuel valve at the dryer, and press the dryer power stop button. Turn OFF the dryer’s main circuit
breaker located on the front of the power panel. Turn OFF the main power supply to the dryer.
the fuel valve at the dryer, and press the dryer power stop button. Turn OFF the dryer’s main circuit
breaker located on the front of the power panel. Turn OFF the main power supply to the dryer.
17. In case of an emergency, press the dryer power stop button. The burner, fan and all augers will
stop immediately.