Beko za630 Manuale Utente
6
REPOSITIONING THE DOOR
Follow the step by step instructions and the diagram below. Numbers in brackets
refer to diagrams.
7
1. Switch off at the socket outlet and pull out the mains plug.
2. Remove all food, loose items and fittings from inside the appliance and door
shelves.
3. Carefully tilt the appliance on its back side. (1) (You may need somebody to
help you.) Take care not to damage the appliance by laying on
some protective material (e.g. its original packaging). Make sure that you tilt
the appliance on its back side, otherwise compressor oil may block the
pipes and you may damage the appliance.
4. Unscrew and remove the LHS front feet (2).
5. Unscrew the bolts and remove the bottom hinge while holding the door (3).
6. Remove the door carefully from the top hinge by sliding towards the right
hand side (4).
7. Reposition top hinge bushing and blanking plug on the opposite side and
stand the door safely (5). You may find it easier to remove the bushing and
the plug with the tip of a small screwdriver. Take care not to mark the door.
8. Reposition the top hinge on the opposite side (6 and 13).
9. Remove the top trim bottom cover as shown in the figure. (7) Cut the shaded part from
left hand side of top trim bottom cover.
10. Fit the top trim bottom cover as shown in the figure. (8)
2. Remove all food, loose items and fittings from inside the appliance and door
shelves.
3. Carefully tilt the appliance on its back side. (1) (You may need somebody to
help you.) Take care not to damage the appliance by laying on
some protective material (e.g. its original packaging). Make sure that you tilt
the appliance on its back side, otherwise compressor oil may block the
pipes and you may damage the appliance.
4. Unscrew and remove the LHS front feet (2).
5. Unscrew the bolts and remove the bottom hinge while holding the door (3).
6. Remove the door carefully from the top hinge by sliding towards the right
hand side (4).
7. Reposition top hinge bushing and blanking plug on the opposite side and
stand the door safely (5). You may find it easier to remove the bushing and
the plug with the tip of a small screwdriver. Take care not to mark the door.
8. Reposition the top hinge on the opposite side (6 and 13).
9. Remove the top trim bottom cover as shown in the figure. (7) Cut the shaded part from
left hand side of top trim bottom cover.
10. Fit the top trim bottom cover as shown in the figure. (8)
11. To refit the door, locate the top hinge in the door, attach to the cabinet and
hold the door (10).
12. Fit the bottom hinge (11). If necessary adjust and then tighten the bolts. Ensure,
that the door opens and closes easily and that there are no gaps allowing air
into the cabinet. If there are gaps between the door seal and the cabinet,
adjust the door seal by gently pulling away from the door using fingers.
13. Fit the other front feet (12).
14. Carefully stand your appliance. (You may need somebody to help you.)
Adjust the front feet (See Installation Instructions)
15. Put back all, loose items and fittings.
16. Wait for at least 4 hours to allow the system to settle before switching on.
Spare plastic parts supplied with the appliance are for your
future use during door repositioning.
hold the door (10).
12. Fit the bottom hinge (11). If necessary adjust and then tighten the bolts. Ensure,
that the door opens and closes easily and that there are no gaps allowing air
into the cabinet. If there are gaps between the door seal and the cabinet,
adjust the door seal by gently pulling away from the door using fingers.
13. Fit the other front feet (12).
14. Carefully stand your appliance. (You may need somebody to help you.)
Adjust the front feet (See Installation Instructions)
15. Put back all, loose items and fittings.
16. Wait for at least 4 hours to allow the system to settle before switching on.
Spare plastic parts supplied with the appliance are for your
future use during door repositioning.
a
b
b
1
60°
7
6
2
3
4
5
10
9
11
8
12