Behringer UMX250 Manuale Utente

U-CONTROL UMX250 User Manual 

The SNAPSHOT command transmits all parameters including 
their current values: all control element assignments as well as 
the current channel settings are sent out from the MIDI OUT 
connector and the USB output of the UMX250.
In this way it is possible to transmit the entire UMX250 
mapping to a sequencer software at the beginning of a song. The 
song can then be played back with the final controller values 
adjusted for it. If the parameters of an external device have been 
changed, you can also use SNAPSHOT to correct the values.

Press the ASSIGN button and keep it pressed.

1) 

Press the SNAP SEND key.

2) 

Release the ASSIGN button. The device automatically enters 

3) 

Play mode again.

The effect of LOCAL OFF is that any data entries made with 
the control elements will NOT be passed on to the MIDI OUT 
connector or the USB OUT. In LOCAL OFF mode you can, for 
example, re-adjust the rotary controls without sending any 
information to the external devices connected—which would 
normally be the case.

Press the ASSIGN button and keep it pressed.

1) 

Press the LOCAL OFF key.

2) 

Release the ASSIGN button and adjust the control elements 

3) 

as required.
Finalize your selection with ENTER, CANCEL or ASSIGN. 

4) 

In either case the ASSIGN LED goes out and the UMX250 
enters Play mode again.

In Chapter 4.2.2 we described how to assign an individual 
channel to each control element. Here you will learn how to 
assign new controllers.
This procedure applies to the MODULATION wheel, the DATA/
VOLUME fader, the rotary controls R1 – R8, the buttons B1 – 
B8 and to the optional sustain pedal connected to jack 

(15)

.

Press the ASSIGN button and keep it pressed.

1) 

Move or press the corresponding controller or button 

2) 

respectively, or hold down the sustain pedal.
Release the ASSIGN button.

3) 

Press the number keys on the keyboard to enter the 

4) 

controller number of your choice. Only values between 0 and 
127 can be entered. Higher values are ignored by the device.

Examples: 
- To enter CC 14 press keys 

(1)

 and 

(4)

. 

- If you want to select CC 107, press 

(1)

, 

(0)

 and 

(7)

.

Press ENTER to confirm. To discard your assignments 

5) 

either press the CANCEL button or the ASSIGN button 
again. In either case the ASSIGN LED goes out.

Please note two special cases with regard to a button or the 
sustain pedal:

The UMX250 provides three options to change programs on 
external devices. This is a very powerful function which allows 
you to fully exploit the multitude of functions of your sound 
modules.
Options a) and b) allow you to select any programs using a 
defined selection procedure. Option c) speeds up the procedure, 
so that you can select programs at the touch of a button.

programs, you can effect program changes in ASSIGN 
mode as shown below. However, if the number of 
128 is exceeded, you will have to use the procedure 
described in section b).
Press the ASSIGN button and keep it pressed.

1) 

Press the SINGLE key.

2) 

Release the ASSIGN button.

3) 

Now define the SINGLE CHANNEL by entering a number 

4) 

from 1 to 16 using the number keys. In order to assign the 
GLOBAL CHANNEL, please press the 

(0)

 instead.

Press the PROGRAM button.

5) 

Press the number keys on the keyboard to enter the program 

6) 

number of your choice. Only values between 0 and 127 can 
be entered. Higher values are ignored by the device.

Examples: 
- To enter program 15, press keys 

(1)

 and 

(5)

  

- If you want to select program 127, press 

(1)

, 

(2)

 and 

(7)

.

Confirm your selection with ENTER. If you do not like the 

7) 

selected program, discard your selection with CANCEL or 
press the ASSIGN button again. In either case, the ASSIGN 
LED goes out.