Westinghouse One-Light Adjustable Mini Pendant 6101000 Manuale Istruttivo
Mini-Pendant Kit
Installation and Safety Instructions
Warning: Be sure the electricity to the wires you are working on is shut off; either the fuse is removed
or the circuit breaker is shut off.
or the circuit breaker is shut off.
General
You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Under no
circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on
a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to
how to proceed, consult a qualified electrician.
You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Under no
circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on
a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to
how to proceed, consult a qualified electrician.
InStallatIon
Important: Do not attach fixture directly to outlet box.
Step 1: Thread mounting screw (A) into the matching hole of mounting bar (B).
Step 2: Secure the mounting bar (B) to outlet box with outlet box screws (C) (not provided).
Important: Do not attach fixture directly to outlet box.
Step 1: Thread mounting screw (A) into the matching hole of mounting bar (B).
Step 2: Secure the mounting bar (B) to outlet box with outlet box screws (C) (not provided).
GroUnDInG anD WIrInG InStrUCtIonS
Step 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the
bare grounding wire (F) from the fixture canopy around the green grounding screw stem (G) on the mounting
bar leaving enough excess wire.
Step 2: Connect the greenish grounding wire (H) from hanging cord (with green label) and excess grounding wire
from the fixture canopy with the grounding wire from outlet box by using a wire connector, then wrap the wire
connector with electrical tape for a more secure connection. WARNING: Never connect grounding wire to black
or white power supply wires.
Step 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the
bare grounding wire (F) from the fixture canopy around the green grounding screw stem (G) on the mounting
bar leaving enough excess wire.
Step 2: Connect the greenish grounding wire (H) from hanging cord (with green label) and excess grounding wire
from the fixture canopy with the grounding wire from outlet box by using a wire connector, then wrap the wire
connector with electrical tape for a more secure connection. WARNING: Never connect grounding wire to black
or white power supply wires.
Step 3: Connect the black house wire with the transparent wires (with black label) by wire connector, and wrap the
wire connector with electrical tape for a more secure connection.
Step 4: Connect the white house wire with the transparent wires (with wite label) by wire connector, and wrap the wire
connector with electrical tape for a more secure connection.
Note: Try to gently pull the connectors off the wires. If you can pull the connector off, carefully repeat steps 2, 3
and 4 above, and check again for a firm connection. Make sure no bare wires can be seen outside wire
connectors.
Step 5: Tighten grounding screw (G). Do not over tighten.
wire connector with electrical tape for a more secure connection.
Step 4: Connect the white house wire with the transparent wires (with wite label) by wire connector, and wrap the wire
connector with electrical tape for a more secure connection.
Note: Try to gently pull the connectors off the wires. If you can pull the connector off, carefully repeat steps 2, 3
and 4 above, and check again for a firm connection. Make sure no bare wires can be seen outside wire
connectors.
Step 5: Tighten grounding screw (G). Do not over tighten.
FInal aSSeMbly
Step 1: After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing the
Step 1: After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing the
mounting screw (A) to protrude through the hole in the canopy (D), and secure with ball nut (E).
Step 2: Install the shade (K) onto the socket (J) and secure the retaining ring (L). (if applicable)
Step 3: Install lamp. (Please do not exceed the maximum capacity recommended on the socket).
Step 2: Install the shade (K) onto the socket (J) and secure the retaining ring (L). (if applicable)
Step 3: Install lamp. (Please do not exceed the maximum capacity recommended on the socket).
CleanInG
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
B
H
G
I
A
*C
F
D
E
J
L
K
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All rights reserved.
Made in China
W-394
071114
*not SUPPlIeD