Roland BR-800 Manuale Utente
Editing
Mastering
Using USB
Con
venient
Functions
Appendix
es
Quic
k Star
t
Getting Read
y
to Recor
d
Recor
ding/
Pla
ybac
k
Using
Eff
ects
Using
Rh
ythm
147
Troubleshooting
Can’t record
Could the song be protected?
Is an SD card inserted?
Could the SD card have insufficient free space?
Could the SD card be locked?
Could you be using the Phrase Trainer?
Could scrub playback be in use?
Could control surface mode be in use?
You can’t record on the BR-800 in control surface mode.
You can’t record on the BR-800 in control surface mode.
You want to turn
off the reverb
off the reverb
Check the reverb send level amounts for the loop effect.
The BR-800 provides reverb as a loop effect.
Reverb is applied by default. If you want to turn off the reverb effect, set each track’s
send level amount to “0.”
The BR-800 provides reverb as a loop effect.
Reverb is applied by default. If you want to turn off the reverb effect, set each track’s
send level amount to “0.”
Recorded sound
contains noise or
distortion
contains noise or
distortion
Is the input sensitivity appropriate?
The recorded sound will be distorted if the input sensitivity is too high, and noise will
be excessive if the input sensitivity is too low. Adjust the input sensitivity so that the
PEAK indicator briefly lights when the loudest passages occur.
The recorded sound will be distorted if the input sensitivity is too high, and noise will
be excessive if the input sensitivity is too low. Adjust the input sensitivity so that the
PEAK indicator briefly lights when the loudest passages occur.
Are the track output levels appropriate?
If there is noise or distortion following mastering, the track output levels are too high.
If there is noise or distortion following mastering, the track output levels are too high.
–
Could a microphone with high output impedance be connected directly to the BR-800?
Since the INPUT 1–4 jacks are designed for a low input impedance, the recording level
may be too low depending on the characteristics of the microphone. In this case, pass the
signal through a commercially available microphone preamp before recording it.
Since the INPUT 1–4 jacks are designed for a low input impedance, the recording level
may be too low depending on the characteristics of the microphone. In this case, pass the
signal through a commercially available microphone preamp before recording it.
–
Oscillation occurs
Could INPUT SELECT be set to “USB”?
If INPUT SELECT is set to “USB,” the settings of your software may cause the audio sig-
nal to be looped. In this case, you can solve the problem by taking one of the following
actions.
If INPUT SELECT is set to “USB,” the settings of your software may cause the audio sig-
nal to be looped. In this case, you can solve the problem by taking one of the following
actions.
• Stop playback in your software, or turn off the Soft Thru function.
• Turn off the audio input of your software.
• Change INPUT SELECT to a setting other than “USB.”
• Turn off the audio input of your software.
• Change INPUT SELECT to a setting other than “USB.”
Problems with the SD Card
Item
Explanation
Page
Data on the SD
card was damaged
card was damaged
Data on the SD card can be damaged due to the following reasons. Please format the SD
card.
card.
• Could you have turned off the power while the recorder was operating?
• Could the SD card have been subjected to strong physical shock?
• Could you have turned off the power while the SD card was being accessed?
• Could you be using an SD card that was formatted by a computer or digital
• Could the SD card have been subjected to strong physical shock?
• Could you have turned off the power while the SD card was being accessed?
• Could you be using an SD card that was formatted by a computer or digital
camera?
Item
Explanation
Page
BR800_e.book 147 ページ ２０１０年３月２日 火曜日 午後６時４０分