Zoom B3 Manuale Utente

 

 

 

The ASIO driver software is required to enable use of Sequel LE for
audio input and output with a computer. Refer to the read_me file
included in the download package for instructions on how to install
the driver correctly. 

 

If the system software is an older version, the product may not be 

recognized properly by the computer. It is therefore recommended to 

always keep the system software updated to the latest version. The 

system software can be downloaded from our web site.

 

 

 

Insert the CD-ROM. When the contents of the CD-ROM are shown,
double-click "Sequel LE2 for Windows" and then select  "Setup.exe".
When the language selection screen appears, choose the language to
use.
After making the selection, follow the instructions on the screen.

 

If nothing happens when you insert the CD-ROM, open the Start menu 

and select "Computer" ("My Computer" in Windows XP). Then 

double-click the "Sequel LE 2 for windows" CD-ROM icon to display 

the contents of the CD-ROM, and double-click the executable file 

"Setup" ("Setup.exe").

 

During the installation of Sequel LE, a screen asking about installation 

of activation (software license authentication) management software 

appears. Install this software, because it is required for registering 

Sequel LE. 

 

 

 

• If you monitor the audio signal during recording via the audio output 

of the computer, there will be an audible delay. Be sure to use the 

[OUTPUT] jack of this unit to monitor the signal.

• When this unit is operated on USB bus power via the USB cable, 

insufficient power may result in unstable operation or error 

indications appearing on the computer screen or unit display.

In such a case, power the device from an AC adapter.

• Use a high-quality USB cable and keep the connection as short as 

possible. If USB bus power is supplied to this unit via a USB cable 

that is more than 3 meters in length, the low voltage warning 

indication may appear.

 

• No special steps are necessary for canceling the USB connection. 

Simply disconnect the USB cable from the computer.

• When you connect this unit for the first time to a computer running 

Windows 7, a message saying "New Hardware Found" will appear. 

Before proceeding, wait a while until this message disappears.

 

To bring up the "Sound" window, select "Control Panel" from the
Start menu and click "Hardware and Sound", then click "Sound". 
 

In the "Sound" window, verify that "ZOOM G Series Audio" is listed
under the Play and Record devices and that the device is checked. (To
switch between Play and Record, click the tabs at the top of the
window.)
If the device is not checked, right-click on the icon for the device and
click "Set as Default Device" so that a check mark appears.

 

To start Sequel LE, double-click the Sequel LE shortcut icon that was
created on the desktop.
After Sequel LE starts, click the button in the bottom left corner of the
Multi Zone area of the Sequel window to open the settings page. Click
the Audio Connection item and select "ZOOM G series ASIO" from
the pop-up menu.
When you change the ASIO driver, a confirmation window will
appear. Click the "Switch" button. 
  

Next, click the "Setup..." button to open a window where you can set
the latency of the ASIO driver. Set the latency as low as possible
without causing the sound to drop out during recording and playback.

[INPUT] jack 

[OUTPUT] jack

 

 

 

The contents of the CD-ROM appear automatically. If nothing
happens when you insert the CD-ROM, double-click the "Sequel LE2
for Mac OS X" icon shown on the desktop.
 

 

When the contents of the CD-ROM are shown, double-click "Sequel
LE 2.mpkg" to install the software.

 

• If you monitor the audio signal during recording via the audio output 

of the computer, there will be an audible delay. Be sure to use the 

[OUTPUT] jack of this unit to monitor the signal.

• When this unit is operated on USB bus power via the USB cable, 

insufficient power may result in unstable operation or error 

indications appearing on the computer screen or unit display.

In such a case, power the device from an AC adapter. 

• Use a high-quality USB cable and keep the connection as short as 

possible. If USB bus power is supplied to this unit via a USB cable 

that is more than 3 meters in length, the low voltage warning 

indication may appear.

 

No special steps are necessary for canceling the USB connection. 

Simply disconnect the USB cable from the computer.

 

 

 

The Audio MIDI Setup screen appears. Click "Audio Devices" and
check whether "USB Audio CODEC" is selected as default input/
default output.

If another item is selected, select the "ZOOM G Series"
After confirming the setting, quit Audio MIDI Setup.
 

 

To launch Sequel LE, click Sequel LE icon in the Applications folder. 
After Sequel LE starts, click the button in the bottom left corner of the
Multi Zone area of the Sequel window to open the settings page. Click
the Audio Connection item and select "ZOOM G series" from the pop-
up menu.
When you change the driver, a confirmation window will appear.
Click the "Switch" button.

Next, click the "Setup..." button to open a window where you can set
the latency (buffer size) of the driver. Set the latency as low as possible
without causing the sound to drop out during recording and playback.

[INPUT] jack 

[OUTPUT] jack