Remington MM251CH Manuale Utente
gET REady To sTaRT
Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as
you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is RED and
located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces.
you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is RED and
located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces.
step 1
Locate the base and place it on the floor. Do not put it up against
the wall at this point in the assembly, as you need to get in behind
the mantel to insert several wingnuts, lock washers and firebox screws.
the wall at this point in the assembly, as you need to get in behind
the mantel to insert several wingnuts, lock washers and firebox screws.
step 2
Locate the left side panel and the left front panel. Facing the front of the base, take
the left side panel, positioning it so the holes in the blocks on the bottom line up
with the holes on the base. Position the left front panel next to the left side panel,
lining up the holes in the blocks with the holes on the base. Attach the left front and
side panel to the base by inserting and tightening 1 wingnut and 1 lock washer to
each piece. Attach the left side and front panels together by inserting and tightening
2 wingnuts and 2 lock washers.
the left side panel, positioning it so the holes in the blocks on the bottom line up
with the holes on the base. Position the left front panel next to the left side panel,
lining up the holes in the blocks with the holes on the base. Attach the left front and
side panel to the base by inserting and tightening 1 wingnut and 1 lock washer to
each piece. Attach the left side and front panels together by inserting and tightening
2 wingnuts and 2 lock washers.
step 3
Repeat Step 2, but with the right side panel and the right front panel.
step 4
Locate the central header that will be attached to the left and right legs and will sit
above the firebox. Position this panel with the finished side facing the front of the
mantel. Line up the holes on each side and insert and tighten 1 wingnut and 1 lock
washer on each side.
above the firebox. Position this panel with the finished side facing the front of the
mantel. Line up the holes on each side and insert and tighten 1 wingnut and 1 lock
washer on each side.
step 5
Get your assistant and locate the top of your mantel. This top is very heavy. It will
take 2 people to lift and position it in place. Ensure the top goes over the positioning
guide located on the header. The top must go over this guide to be positioned
correctly. Line up the holes on the top of the mantel, insert and tighten 5 wing nuts
and lock washers.
take 2 people to lift and position it in place. Ensure the top goes over the positioning
guide located on the header. The top must go over this guide to be positioned
correctly. Line up the holes on the top of the mantel, insert and tighten 5 wing nuts
and lock washers.
635
471
1203
1143
330
889
360
1
2
4
5
7
6
3
TOP
BASE
RIGHT SIDE PANEL
LEFT SIDE PANEL
RIGHT FRONT PANEL
LEFT FRONT PANEL
2PC
2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 18PCS
1
2
2
3
4
4
5
6
1
1
1
1
1
1
1
1
RIGHT SIDE PANEL
MM251CH
MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME
QTY.
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
7
1
TOP
MM251CH
CENTRAL HEADER
SPRING LOCK 18PCS
635
471
1203
1143
330
889
360
1
2
4
5
7
6
3
TOP
BASE
RIGHT SIDE PANEL
LEFT SIDE PANEL
RIGHT FRONT PANEL
LEFT FRONT PANEL
2PC
2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 18PCS
1
2
2
3
4
4
5
6
1
1
1
1
1
1
1
1
RIGHT SIDE PANEL
MM251CH
MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME
QTY.
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
7
1
TOP
MM251CH
CENTRAL HEADER
SPRING LOCK 18PCS
635
471
1203
1143
330
889
360
1
2
4
5
7
6
3
TOP
BASE
RIGHT SIDE PANEL
LEFT SIDE PANEL
RIGHT FRONT PANEL
LEFT FRONT PANEL
2PC
2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 18PCS
1
2
2
3
4
4
5
6
1
1
1
1
1
1
1
1
RIGHT SIDE PANEL
MM251CH
MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME
QTY.
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
7
1
TOP
MM251CH
CENTRAL HEADER
SPRING LOCK 18PCS
635
471
1203
1143
330
889
360
1
2
4
5
7
6
3
TOP
BASE
RIGHT SIDE PANEL
LEFT SIDE PANEL
RIGHT FRONT PANEL
LEFT FRONT PANEL
2PC
2PC
4PCS
FLAT HEAD SCREW(4*30mm)4PCS
FLAT HEAD SCREW(4*16mm)4PCS
WING NUT(5*28) 18PCS
1
2
2
3
4
4
5
6
1
1
1
1
1
1
1
1
RIGHT SIDE PANEL
MM251CH
MODEL
ITEM NAME
PART NO.
MANTEL
PART NAME
QTY.
BASE
CENTRAL HEADER
RIGHT FRONT PANEL
LEFT SIDE PANEL
LEFT FRONT PANEL
7
1
TOP
MM251CH
CENTRAL HEADER
SPRING LOCK 18PCS
Step 1
Step 2 & 3
Step 4
Step 5
2