RCA SSM-1750 Manuale Utente
9
Operation
Notes:
• If it was necessary to set the channel
volume level slide control to
10
to get a
reading of up to
0
on the VU meter, then
slide it down to about
8
and adjust the
GAIN
control to get a reading of up to
0
on the VU meters. (See “Using Gain” on
Page 11.)
Page 11.)
• If the above does not work, set
GAIN
to
mid level and rotate
MASTER
clockwise
until you get a reading of
0
on the VU
meters.
• Readjusting
MASTER
affects the level of
the previously set input sources.
You
must readjust those sources until you
get a reading of up to
get a reading of up to
0
on the VU
meters for each input source.
5. Stop playback of the selected input
source.
6. Repeat these steps for each channel
input you plan to mix.
Presetting a Microphone
1. If your XLR or auxiliary microphone has
an ON/OFF control, set it to ON.
If your XLR or auxiliary microphone
does not have an ON/OFF control, set
does not have an ON/OFF control, set
DJ MIC LEVEL
or
AUX LEVEL
to
0
.
2. While talking continuously, adjust
DJ MIC
LEVEL
or
AUX LEVEL
until you get a
reading of up to
0
on both VU meters.
(See “Using an XLR Microphone” on
Page 12 and “Using an AUX Micro-
phone” on Page 12.)
Page 12 and “Using an AUX Micro-
phone” on Page 12.)
Important: Note the
DJ MIC LEVEL
or
AUX
LEVEL
setting, so each time you want to mix
the microphone, you can set the control to
the correct setting.
the correct setting.
Notes:
• If it was necessary to set
DJ MIC LEVEL
or
AUX LEVEL
all the way to
10
in order
to get a reading of up to
0
on the VU
meter, then turn it down to about
8
and
adjust the
DJ MIC GAIN
control to get a
reading of up to
0
on the VU meters.
(See “Using Gain” on Page 11.)
If that does not work, set
DJ MIC GAIN
or
AUX GAIN
to mid level and rotate
MAS-
TER
clockwise until you get a reading of
0
on the VU meters.
• If you must readjust
MASTER
, remem-
ber, doing so affects the level of the pre-
viously set input sources. You must
readjust those sources until you get a
reading of up to
viously set input sources. You must
readjust those sources until you get a
reading of up to
0
on the VU meters for
each input source.
3.
I
f your XLR or auxiliary microphone has
an ON/OFF control, set it to OFF.
If your XLR or auxiliary microphone
does not have an ON/OFF control, set
does not have an ON/OFF control, set
DJ MIC LEVEL
or
AUX LEVEL
to
0
.
Presetting the Auxiliary Input
1. To preset the
AUX LINE
input source, set
AUX
to
LINE
.
2. Start playback of the selected input
source.
3. Adjust the
HIGH
,
MID
, and
BASS
controls
as desired. See “Using the Tone Con-
trols” on Page 11.
trols” on Page 11.
Note: If you are using an external equal-
izer, leave the tone controls set to
izer, leave the tone controls set to
0
and
adjust the tone on the external equalizer.
4. Slowly adjust
AUX LEVEL
until you get a
reading of
0
on both VU meters.
32-3008.fm Page 9 Thursday, April 6, 2000 4:03 PM