Pioneer Plasma Display PDP-614MX Manuale Utente

En

FULL size screen

The  image  is  expanded  in  the  horizontal  and  vertical
direction.

ZOOM size screen

When wide signals are input.

FULL

DOT BY DOT

The image is dot by dot resolution.
* “D BY D” can be switched only when a 1280 dot 

 768

line signal is input.

Information
 Supported resolution
See  page  30  for  details  on  the  display  output  of  the
various  VESA  signal  standards  supported  by  the
monitor.
 “PICTURE SIZE” setting
When the setting of “PICTURE SIZE” is OFF, the size
of RGB-input pictures will be D BY D in place of 4:3.
 When 852 (848) dot  480 line wide VGA*
signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31.0) kHz are in-
put
Select an appropriate setting for RGB SELECT mode
referring to the“Table of Signals Supported” on page
30.

* “VGA”,  “SVGA”  and  “SXGA”  are  registered

trademarks of IBM, Inc. of the United States.

Switch to the wide screen mode to expand the 4 : 3 image
to fill the entire screen.

1. Press the SCREEN SIZE button on the remote control.

2. Within 3 seconds ...

Press the SCREEN SIZE button again.
The screen size switches as follows:

A 4:3 A FULL A ZOOM

4:3 size screen (4:3 or SXGA 5:4)

The picture has the same size as the normal computer image.

FULL size screen

The image is expanded in the horizontal direction.

ZOOM size screen

When wide signals are input.

FULL size screen

When “PICTURE SIZE” is set to “OFF”
* This cannot be set in some models. “DOT BY DOT” will

not be displayed in such cases.

The screen size switches as follows:

A D BY D A FULL A ZOOM

DOT BY DOT screen (VGA, SVGA 4:3)

The image is dot by dot resolution.

En

The OSD window is displayed with respect to the
screen as shown on the diagram.

* Depending  on  the  screen’s  mode,  the  OSD  may  be

displayed differently.
In the explanation, the OSD section is shown close up.

The  following  describes  how  to  use  the  menus  and  the
selected items.
1. Press  the  MENU/SET  button  on  the  remote  control  to

display the MAIN MENU.

2. Press the cursor buttons 

▲ ▼ on the remote control to

highlight the menu you wish to enter.

3. Press  the  MENU/SET  button  on  the  remote  control  to

select a sub menu or item.

4. Adjust the level or change the setting of the selected item

by using the cursor buttons 



  



 on the remote control.

5. The adjustments or the settings that are stored in memory.

The change is stored until you change it again.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the  EXIT  button  on  the  remote  control  to  return  to  the
main menu.

* When adjusting using the bar at the bottom of the screen,

press the 



 or 



 button within 5 seconds. If not, the

current setting is set and the previous screen appears.

Information
 Advanced menu mode
When “ADVANCED OSD” is set to “ON” in the main
menu (1/2), full menu items will be shown.

The menu display can be set to one of seven languages.

Example: Setting the menu display to “DEUTSCH”

On “MAIN MENU”, select “LANGUAGE”, then press the
MENU/SET button.
The “LANGUAGE” screen appears.
On  “LANGUAGE”,  select  “  DEUTSCH”,  then  press  the
MENU/SET button.

The “LANGUAGE” is set to “DEUTSCH” and return to the
main menu.

Information
 Language settings
ENGLISH ........ English
DEUTSCH ....... German
FRANÇAIS ......  French
ESPAÑOL ....... Spanish

ITALIANO ........ Italian
SVENSKA ....... Swedish

................ Japanese