Tyco 0-1591099-x Manuale Utente
24 Port Stackable Managed Switch – User Guide Page 34
RSTP Setup
To enable Spanning Tree highlight ‘Set RSTP Mode’ using the <tab> key and press <enter>.
The RSTP Setup screen will now appear. Select <edit> mode from the action line and use the
<spacebar> to toggle between STP modes. Choose either 802.1w (RSTP) or 802.1d
(Traditional Spanning Tree) depending what type of spanning tree protocol is required. Now
use the <esc> key to return to the action line and then <apply> the changes. Spanning Tree
is now enabled on the Switch.
The RSTP Setup screen will now appear. Select <edit> mode from the action line and use the
<spacebar> to toggle between STP modes. Choose either 802.1w (RSTP) or 802.1d
(Traditional Spanning Tree) depending what type of spanning tree protocol is required. Now
use the <esc> key to return to the action line and then <apply> the changes. Spanning Tree
is now enabled on the Switch.
System Configuration
This screen provides both information and configuration of the spanning tree protocol. Useful
information such as Root Bridge, Root Port and cost to root can be gathered from here. The
following parameters can also be changed from this menu:
information such as Root Bridge, Root Port and cost to root can be gathered from here. The
following parameters can also be changed from this menu:
•
Priority – This parameter allows the control of Root Bridge in the STP network. The
lower the priority, the more likely this Switch will be elected as root. The valid range
is 1 - 65535.
lower the priority, the more likely this Switch will be elected as root. The valid range
is 1 - 65535.
•
Max Age - The number of seconds the Switch waits for hello messages from root
bridge before deciding the root is unavailable and performing a reconfiguration. The
valid range is 6 - 40.
bridge before deciding the root is unavailable and performing a reconfiguration. The
valid range is 6 - 40.
•
Hello Time – This is the interval in time (seconds) that a root bridge sends BPDU
configuration messages. The valid range is 1 - 10.
configuration messages. The valid range is 1 - 10.
•
Forward Delay Time – The period in time (seconds) a Switch will wait (the listen
and learn period) before forwarding frames. The valid range is 4 - 30.
and learn period) before forwarding frames. The valid range is 4 - 30.
Per Port Setting
This screen allows the individual RSTP/STP values to be set on the required ports. . A port
with higher priority, lower path cost is less likely to be blocked if Spanning Tree Protocol
detects a network loop. The following can be configured:
with higher priority, lower path cost is less likely to be blocked if Spanning Tree Protocol
detects a network loop. The following can be configured:
•
Path Cost – This parameter can be used to assign a higher or lower path cost to a
port. A port with a high path cost is more likely to be blocked. The valid range is 1 -
200000000.
port. A port with a high path cost is more likely to be blocked. The valid range is 1 -
200000000.
•
Priority – If path cost to root is equal then a port with a higher priority (lower
numerical value) is more likely to forward traffic. The valid range is 1 - 240.
numerical value) is more likely to forward traffic. The valid range is 1 - 240.
•
P2P – This parameter is used by RSTP to determine if the port is connected to a
shared or full-duplex link, which will affect RSTP state transaction. It is
recommended to keep this parameter with the default of Auto.
shared or full-duplex link, which will affect RSTP state transaction. It is
recommended to keep this parameter with the default of Auto.
•
Edge – This is a RSTP value. A port directly connected to end stations cannot
create a bridging loop. The default is true.
create a bridging loop. The default is true.
•
Non STP – The status shown here indicates if the port is participating in STP.
Per Port Status
This is informational screen only and parameters cannot be changed. The STP status
of each port can be viewed. The following STP port statuses are:
•
Role – indicates the STP role of the port
•
State – determines the STP state of the port
•
Path Cost – The port cost.
•
P2P – The current P2P status of the port
•
Edge – The current Edge status of the port
•
STP Neighbor – shows if the port has a STP neighbor or not.
Product Number 0-1591099-x © Tyco Electronics 2005
Issue 1