NEC 2400 PX Manuale Utente
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
NDA-24297, Issue 1
Page 995
Number Portability - CCIS
N-46
Service Conditions (cont’d)
Legend:
*
Destination node
**
Node to be connected to the FCCS group where the new number is added
***
Node where the telephone number is located before the Number Portability activation
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Assign FCCS data following FCCS Data Assignment Procedure in the NEAX2400 IPX No. 7 CCIS
System Manual.
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Assign FCCS data following FCCS Data Assignment Procedure in the NEAX2400 IPX No. 7 CCIS
System Manual.
STEP 1:
Set the data for the Centralized MAT following programming of Centralized Maintenance - CCIS [C-
167]. Note that AEADN command in STEP 2 and AELGN command in STEP 3 are not valid when the
self FCCS group (self-FUG) number has not been assigned by the AFUGN command.
167]. Note that AEADN command in STEP 2 and AELGN command in STEP 3 are not valid when the
self FCCS group (self-FUG) number has not been assigned by the AFUGN command.
STEP 2:
AEADN
- Assign Abbreviated Digit Code (ADC) for connected FUG. Enter the FUG number
assigned by AFUGN command, TN, and ADC to be assigned.
FUG:
FCCS group number of destination group (1-4)
Note 1
Note 1:
The self-FUG cannot be entered.
TN:
Tenant number
ADC:
Abbreviated Digit Code for the destination FUG (maximum of 6 digits)
STEP 3:
AELGN
- Assign telephone number (must be a unique number in the network). When assigning the
data logging in to the NCN of Center FUG by using this command, the data in NDM of all the LNs in
the self-FUG and NCN/LN in other FUGs are updated simultaneously.
the self-FUG and NCN/LN in other FUGs are updated simultaneously.
UGN: Fixed to 1
TELN: Enter the unique telephone number (maximum of 6 digits)
NO.
PATTERN (TELEPHONE NUMBER IS MOVED FROM A TO B)
NODE REQUIRING DATA CHANGE
1.
Moving number within the same FCCS group.
NCN in Center FCCS group
2.
Moving number in FCCS group to another FCCS group.
NCN in Center FCCS group
3.
Moving number in FCCS group to NEAX2000 IVS
2
NCN in Center FCCS group +
NEAX2000 IVS
NEAX2000 IVS
2
*
4.
Adding new number to FCCS group
NCN in Center FCCS group +
NEAX2000 IVS
NEAX2000 IVS
2
**
5.
Moving number in NEAX2000 IVS
2
to FCCS group
NCN in Center FCCS group +
NEAX2000 IVS
NEAX2000 IVS
2
***
6.
Moving number from NEAX2000 IVS
2
to another NEAX2000
IVS
2
NCN in Center FCCS group +
NEAX2000 IVS
NEAX2000 IVS
2
*** + another
NEAX2000 IVS
2
*
7.
Moving number within the same NEAX2000 IVS
2
NEAX2000 IVS
2
*, ***
8.
Adding new number in NEAX2000 IVS
2
NCN in Center FCCS group +
NEAX2000 IVS
NEAX2000 IVS
2
*