NEC 2400 PX Manuale Utente
NEAX2400 IPX Feature Programming Manual
Page 122
NDA-24297, Issue 1
C-3
Call Forwarding - Don’t Answer
Service Conditions (cont’d)
20.
When a call is forwarded through FCCS link, the numbering plan of the originally called station must be
identical with the one of the forwarded Attendant Console.
identical with the one of the forwarded Attendant Console.
21.
If individual Call Forwarding - Don’t Answer timer is not given, the default timer assigned by ASYD
command is used.
command is used.
Interactions
1.
If access codes for CALL FORWARDING-BUSY LINE and CALL FORWARDING-DON’T ANSWER
are the same, only one key needs to be assigned in AKYD.
are the same, only one key needs to be assigned in AKYD.
2.
ACFO is applicable to DID, DIT, and TIE Line calls only.
3.
A non-controlling UCD station is allowed to activate CALL FORWARDING-DON’T ANSWER. When
this station sets call forwarding, calls directed to this station will be call forwarded. The member station
is not removed from the UCD group under the conditions of the call forwarding feature used. When it is
the station’s turn to ring, that call is affected by CALL FORWARDING-DON’T ANSWER.
this station sets call forwarding, calls directed to this station will be call forwarded. The member station
is not removed from the UCD group under the conditions of the call forwarding feature used. When it is
the station’s turn to ring, that call is affected by CALL FORWARDING-DON’T ANSWER.
4.
CALL FORWARDING-DON’T ANSWER to an Attendant Console will not operate when the system is
in Night mode. If ATTENDANT NIGHT TRANSFER [A-19] is provided, the call is forwarded to the
ATTENDANT NIGHT TRANSFER [A-19] station.
in Night mode. If ATTENDANT NIGHT TRANSFER [A-19] is provided, the call is forwarded to the
ATTENDANT NIGHT TRANSFER [A-19] station.
5.
If the CALL FORWARDING-DON’T ANSWER target station is a D
term
that has activated DO NOT
DISTURB [D-21D], call forwarding is not activated.
6.
The CALL FORWARDING-DON’T ANSWER feature is set from Station A to Station B if Station A is
idle and Station B is busy.
idle and Station B is busy.
7.
When a call is Call Forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
RECORDING [S-10].
8.
STATION-TO-STATION CALLING [S-11] must first be provided.
Programming
STEP 1:
ASYD
- System Data 1, Index 5, Bit 0. Are the access codes for CALL FORWARDING - BUSY
LINE [C-2] and CALL FORWARDING - DON’T ANSWER the same or separate? 0/1: Same/
Separate.
Separate.
System Data 1, Index 69, Bit 1 and 2 is a short tone to alert person receiving the call that this is a
CALL FORWARDING-DON’T ANSWER call? 0/1: No/Yes.
System Data 1, Index 139. Assign the No Answer timer for station-to-station, DID and TIE Line calls.
For 30 seconds, assign 00H. [RAM data is 3FH].
System Data 1, Index 141. Assign the No Answer timer for incoming calls via the Attendant Console.
It will then be forwarded to the next station according to SYS1, Index 145 timer. For 10 seconds assign
00H. [RAM data is 3FH.]
CALL FORWARDING-DON’T ANSWER call? 0/1: No/Yes.
System Data 1, Index 139. Assign the No Answer timer for station-to-station, DID and TIE Line calls.
For 30 seconds, assign 00H. [RAM data is 3FH].
System Data 1, Index 141. Assign the No Answer timer for incoming calls via the Attendant Console.
It will then be forwarded to the next station according to SYS1, Index 145 timer. For 10 seconds assign
00H. [RAM data is 3FH.]
TK
Node
A
Node
B
FCCS Link
Station A has been set
Call Forwarding service to
Attendant Console B
Call Forwarding service to
Attendant Console B
Attendant
Console B
Console B