NEC 2400 PX Manuale Utente
NEAX2400 IPX Feature Programming Manual
Page 132
NDA-24297, Issue 1
C-5
Call Forwarding - All Calls
Interactions (cont’d)
7.
When CALL FORWARDING-ALL CALLS is in effect, the activating station may be used to originate
calls. See System Data 2, Index 6, Bit 4.
calls. See System Data 2, Index 6, Bit 4.
8.
When a station is call forwarded, the destination station is recorded for STATION MESSAGE DETAIL
RECORDING [S-10].
RECORDING [S-10].
9.
CALL FORWARDING-ALL CALLS can be overridden, allowing Station B to initiate or transfer calls
back to Station A.
back to Station A.
10.
STATION-TO-STATION CALLING [S-11] must first be provided.
Programming
STEP 1:
ASYD
- System Data 1, Index 4, Bit 6. One burst of ringing at the forwarding station when CALL
FORWARDING-ALL CALLS is in service? 01: No/Yes.
System Data 1, Index 248, Bit 7. Dial tone to be sent out when a station on which CALL
FORWARDING-ALL CALLS is set, goes off-hook to place an outgoing call 0/1: Dial Tone/Special
Dial Tone.
System Data 1, Index 69, Bit 1 (Bit 2 - Call Forward Recall Tone). A burst of ringback tone to alert the
person receiving a call that this is a CALL FORWARDING-ALL CALLS call. In service? 0/1: No/
Yes. Normally assigned as data “0”.
FORWARDING-ALL CALLS is set, goes off-hook to place an outgoing call 0/1: Dial Tone/Special
Dial Tone.
System Data 1, Index 69, Bit 1 (Bit 2 - Call Forward Recall Tone). A burst of ringback tone to alert the
person receiving a call that this is a CALL FORWARDING-ALL CALLS call. In service? 0/1: No/
Yes. Normally assigned as data “0”.
System Data 2, Index 6, Bit 4. Enable station set for CALL FORWARDING-ALL CALLS be allowed
to use phones normally. If data “0” is assigned, the station will only be able to call the Attendant
Console. Assign on a per-tenant basis.
to use phones normally. If data “0” is assigned, the station will only be able to call the Attendant
Console. Assign on a per-tenant basis.
STEP 2:
ANPD
- Reserve a number level for feature access and cancel. Assign Connection Index, (CI) = N, H,
B; Normal, Hooking, and Busy (applicable to any feature assigned to this level). Assign NND in
accordance with a predetermined numbering plan.
accordance with a predetermined numbering plan.
STEP 3:
ASPA
- Assign an access code to CALL FORWARDING-ALL CALLS entry SID = 8, and to CALL
FORWARDING-ALL CALLS cancel SID = 9. Assign CI for Normal (N) service.
STEP 4:
ASFC
- Assign a Service Feature Class that allows SFI = 7 to stations that will activate CALL
FORWARDING - ALL CALLS.
STEP 5:
AKYD
- For D
term
sets, CALL FORWARDING-ALL CALLS may be assigned to a programmable
line/feature key. Assign Type:Function:CALL FORWARDING-ALL CALLS [2].
STEP 6:
ATNR
- Allow tenant-to-tenant connection for Inter and Intra-tenant connections. Assign Tenant
Restriction Index (TRI) = 1. For this feature to be set by the Attendant Console, assign Inter an Intra-
Tenant connection TRI = 3, via the attendant Console. Also allow TRI = 0, station-to-station calling.
Tenant connection TRI = 3, via the attendant Console. Also allow TRI = 0, station-to-station calling.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note 1
STEP 1:
ASYDL
- This data must be assigned to the node set Call Forwarding service.
System Data 1, Index 640: Assign the FPC of the node providing the attendant console.
Note 1:
When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN.
in addition to ASYDL or ASYDN.
Note 2:
The data of the ASFC command is assigned to the node set Call Forwarding service.