NEC 2400 PX Manuale Utente
NEAX2400 IPX Feature Programming Manual
Page 574
NDA-24297, Issue 1
P-1
Paging Access
P-1 Paging
Access
General Description
This feature provides both ATTENDANT CONSOLE [A-3] and users dial access to PAGING equipment.
Operating Procedure
1.
Go off-hook; receive dial tone.
2.
Dial the Paging access code; receive ringback tone for several seconds.
3.
Connection to Paging equipment is established.
Service Conditions
1.
Amplifiers and speakers must be customer provided.
2.
One trunk circuit is required for each Paging Access.
3.
Where TENANT SERVICE [T-12] is provided, separate access codes and hardware should be provided
for each tenant.
for each tenant.
4.
Maximum Paging Access code is 3 digits.
5.
ALL ZONE PAGING [A-53]: If the system provides multi-zone Paging with a separate direct access code
assigned for each area, stations or Attendants can use all-zone Paging by dialing a special access code
common for all Paging systems.
assigned for each area, stations or Attendants can use all-zone Paging by dialing a special access code
common for all Paging systems.
6.
PRIORITY PAGING [P-30]: A predetermined station or the Attendant can preempt a Paging trunk that is
connected to any station.
connected to any station.
7.
Loop signaling is the recommended signaling type.
8.
PAGING ACCESS [P-1], PAGING TRANSFER [P-10] and RADIO PAGING [R-16] are provided to the
paging station and the paged station in FCCS nodes.
paging station and the paged station in FCCS nodes.
9.
When PAGING ACCESS [P-1]/PAGING TRANSFER [P-10]/RADIO PAGING [R-16] service is set to
a station in the remote node or the PAGING ACCESS [P-1]/PAGING TRANSFER [P-10]/RADIO
PAGING [R-16] call is answered from the remote node via FCCS link:
a station in the remote node or the PAGING ACCESS [P-1]/PAGING TRANSFER [P-10]/RADIO
PAGING [R-16] call is answered from the remote node via FCCS link:
a.) the logical route number should be applied to each physical route that provides the service.
b.) the restriction of route-to-route connection between FCCS nodes should be released.
b.) the restriction of route-to-route connection between FCCS nodes should be released.
10.
The same paging route cannot be used by another station while the paged station does not answer the page
activated using the route. However, the paging activation is automatically cleared when the call is not
answered within a predetermined time.
activated using the route. However, the paging activation is automatically cleared when the call is not
answered within a predetermined time.
11.
A user can page one station at a time.
Interactions
1.
MEET-ME PAGING [M-1, 11] and PAGING ACCESS [P-1] can be provided simultaneously in the same
system.
system.
2.
To directly answer PAGING ACCESS [P-1] by the Attendant Console, the Paged party should use the
INDIVIDUAL ATTENDANT ACCESS [I-4] feature.
INDIVIDUAL ATTENDANT ACCESS [I-4] feature.
3.
Paging is limited to stations, Attendant Consoles, or TIE trunks. Other parties (CO trunks calls) must have
the Attendant Console or user perform the Paging operation.
the Attendant Console or user perform the Paging operation.
4.
BUSY VERIFICATION [B-3], EXECUTIVE OVERRIDE [E-1]: These features will be denied if the
Paging route has been assigned for Privacy. Verify the data in the Assignment of Route Data command,
ARTD, CDN 44:PRV. If CDN 6:TCL is assigned as data “8”, CDN 44:PRV is not required.
Paging route has been assigned for Privacy. Verify the data in the Assignment of Route Data command,
ARTD, CDN 44:PRV. If CDN 6:TCL is assigned as data “8”, CDN 44:PRV is not required.