NEC 2400 PX Manuale Utente
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
NDA-24297, Issue 1
Page 745
Toll Denial/Toll Diversion
T-6
T-6 Toll
Denial/Toll
Diversion
General Description
This feature prohibits users from placing long distance calls over a specific group of trunks. Restricted calls are
routed to either an ATTENDANT CONSOLE [A-3] (diversion) or to an intercept tone (denial).
routed to either an ATTENDANT CONSOLE [A-3] (diversion) or to an intercept tone (denial).
Operating Procedure
No manual operation is required after this feature is programmed into system data.
Service Conditions
1.
TOLL DENIAL/TOLL DIVERSION is the industry-standard 0/1 type.
2.
Immediately after dialing any area code with a second digit of “0” or “1”, the user is restricted.
3.
Restriction may be programmed to give the user a busy signal or to divert the user to the Attendant
Console.
Console.
4.
This feature may be applied to all types of trunks (DDD, FX, WATS), provided the same restrictions apply
to all trunks of the same type.
to all trunks of the same type.
5.
This feature is applied to individual stations on a route-restriction basis.
6.
TOLL DENIAL/TOLL DIVERSION is set on a per-TENANT [T-12] basis.
7.
The 0/1 Toll Denial and Toll Diversion feature cannot be used together for the same tenant.
8.
The 0/1 Toll Denial and Toll Diversion feature is assigned on a per-line (RSC) Class of Service and/or
per-incoming TIE Trunk group basis. The feature, when provided, is applicable on a per-trunk group basis.
per-incoming TIE Trunk group basis. The feature, when provided, is applicable on a per-trunk group basis.
Interactions
1.
TOLL DENIAL/DIVERSION is applicable only to RES 2 when assigning routes via Route Restriction
Index (RRI) 3.
Index (RRI) 3.
2.
LEAST-COST ROUTING-3/6 DIGIT [L-5]: For LCR(S) applications, allow the LCR Flag Route. The
route chosen via AOPR will then be governed by the RSC of the station. If the station is toll-restricted
from the route, TOLL DENIAL/DIVERSION will apply
route chosen via AOPR will then be governed by the RSC of the station. If the station is toll-restricted
from the route, TOLL DENIAL/DIVERSION will apply
3.
TOLL DENIAL and TOLL DIVERSION cannot be used simultaneously in the same tenant.
4.
ROUTE ADVANCE [R-6]: Station A dials a toll call by accessing route 1. Route 1 is busy and advances
to route 2. Station A is restricted from making this call on route 2.
to route 2. Station A is restricted from making this call on route 2.
5.
PASSING DIAL TONE [P-2]: The Attendant Console cannot use the PASSING DIAL TONE [P-2]
feature to allow a toll restricted station to dial a restricted number.
feature to allow a toll restricted station to dial a restricted number.
6.
In System Data 1, Index 135, a seizure guard timer exists to protect the system from individuals who
attempt to defeat TOLL RESTRICTION/TOLL DIVERSION with rapid dialing. Leave as data “00” for
a default value of 1 second (RAM data is 1FH).
attempt to defeat TOLL RESTRICTION/TOLL DIVERSION with rapid dialing. Leave as data “00” for
a default value of 1 second (RAM data is 1FH).
7.
A station uses the OGC direct dial access to a route. The station is restricted via RES 0: Connection
Restricted. The station receives reorder tone.
Restricted. The station receives reorder tone.
Programming
STEP 1:
ASYD
- System Data 1, Index 75. Should the following commands be developed for Day/Night: 0/1:
No/Yes. See DAY/NIGHT CLASS OF SERVICE
for details.
Bit 0- Develop ARSC command for Day/Night?