National CP3BT26 Manuale Utente
193
www.national.com
CP3
BT26
25.3
WATCHDOG OPERATION
The Watchdog is an 8-bit down counter that operates on the
rising edge of a specified clock source. At reset, the Watch-
dog is disabled; it does not count and no Watchdog signal is
generated. A write to either the Watchdog Count (WDCNT)
register or the Watchdog Service Data Match (WDSDM)
register starts the counter. The Watchdog counter counts
down from the value programmed in the WDCNT register.
Once started, only a reset can stop the Watchdog from op-
erating.
rising edge of a specified clock source. At reset, the Watch-
dog is disabled; it does not count and no Watchdog signal is
generated. A write to either the Watchdog Count (WDCNT)
register or the Watchdog Service Data Match (WDSDM)
register starts the counter. The Watchdog counter counts
down from the value programmed in the WDCNT register.
Once started, only a reset can stop the Watchdog from op-
erating.
The Watchdog can be programmed to use either T0OUT or
T0IN as its clock source (the output and input of Timer T0,
respectively). The TWCFG.WDCT0I bit controls this clock
selection.
T0IN as its clock source (the output and input of Timer T0,
respectively). The TWCFG.WDCT0I bit controls this clock
selection.
Software must periodically “service” the Watchdog. There
are two ways to service the Watchdog, the choice depend-
ing on the programmed value of the WDSDME bit in the
Timer and Watchdog Configuration (TWCFG) register.
are two ways to service the Watchdog, the choice depend-
ing on the programmed value of the WDSDME bit in the
Timer and Watchdog Configuration (TWCFG) register.
If the TWCFG.WDSDME bit is clear, the Watchdog is ser-
viced by writing a value to the WDCNT register. The value
written to the register is reloaded into the Watchdog counter.
The counter then continues counting down from that value.
viced by writing a value to the WDCNT register. The value
written to the register is reloaded into the Watchdog counter.
The counter then continues counting down from that value.
If the TWCFG.WDSDME bit is set, the Watchdog is ser-
viced by writing the value 5Ch to the Watchdog Service
Data Match (WDSDM) register. This reloads the Watchdog
counter with the value previously programmed into the WD-
CNT register. The counter then continues counting down
from that value.
viced by writing the value 5Ch to the Watchdog Service
Data Match (WDSDM) register. This reloads the Watchdog
counter with the value previously programmed into the WD-
CNT register. The counter then continues counting down
from that value.
A Watchdog error signal is generated by any of the following
events:
events:
The Watchdog serviced too late.
The Watchdog serviced too often.
The WDSDM register is written with a value other than
The Watchdog serviced too often.
The WDSDM register is written with a value other than
5Ch when WDSDM type servicing is enabled
(TWCFG.WDSDME = 1).
(TWCFG.WDSDME = 1).
A Watchdog error condition resets the device.
25.3.1
Register Locking
The Timer and Watchdog Configuration (TWCFG) register
is used to set the Watchdog configuration. It controls the
Watchdog clock source (T0IN or T0OUT), the type of
Watchdog servicing (using WDCNT or WDSDM), and the
locking state of the TWCFG, TWCPR, TIMER0, T0CSR,
and WDCNT registers. A register that is locked cannot be
read or written. A write operation is ignored and a read op-
eration returns unpredictable results.
is used to set the Watchdog configuration. It controls the
Watchdog clock source (T0IN or T0OUT), the type of
Watchdog servicing (using WDCNT or WDSDM), and the
locking state of the TWCFG, TWCPR, TIMER0, T0CSR,
and WDCNT registers. A register that is locked cannot be
read or written. A write operation is ignored and a read op-
eration returns unpredictable results.
If the TWCFG register is itself locked, it remains locked until
the device is reset. Any other locked registers also remain
locked until the device is reset. This feature prevents a run-
away program from tampering with the programmed Watch-
dog function.
the device is reset. Any other locked registers also remain
locked until the device is reset. This feature prevents a run-
away program from tampering with the programmed Watch-
dog function.
25.3.2
Power Save Mode Operation
The Timer and Watchdog Module is active in both the Power
Save and Idle modes. The clocks and counters continue to
operate normally in these modes. The WDSDM register is
accessible in the Power Save and Idle modes, but the other
TWM registers are accessible only in the Active mode.
Therefore, Watchdog servicing must be carried out using
the WDSDM register in the Power Save or Idle mode.
Save and Idle modes. The clocks and counters continue to
operate normally in these modes. The WDSDM register is
accessible in the Power Save and Idle modes, but the other
TWM registers are accessible only in the Active mode.
Therefore, Watchdog servicing must be carried out using
the WDSDM register in the Power Save or Idle mode.
In the Halt mode, the entire device is frozen, including the
Timer and Watchdog Module. On return to Active mode, op-
eration of the module resumes at the point at which it was
stopped.
Timer and Watchdog Module. On return to Active mode, op-
eration of the module resumes at the point at which it was
stopped.
Note: After a restart or Watchdog service through WDCNT,
do not enter Power Save mode for a period equivalent to 5
Slow Clock cycles.
do not enter Power Save mode for a period equivalent to 5
Slow Clock cycles.
25.4
TWM REGISTERS
The TWM registers controls the operation of the Timing and
Watchdog Module. There are six such registers:
Watchdog Module. There are six such registers:
The WDSDM register is accessible in both Active and Pow-
er Save mode. The other TWM registers are accessible only
in Active mode.
er Save mode. The other TWM registers are accessible only
in Active mode.
Table 76
TWM Registers
Name
Address
Description
TWCFG
FF FF20h
Timer and Watchdog
Configuration Register
TWCP
FF FF22h
Timer and Watchdog
Clock Prescaler
Register
TWMT0
FF FF24h
TWM Timer 0 Register
T0CSR
FF FF26h
TWMT0 Control and
Status Register
WDCNT
FF FF28h
Watchdog Count
Register
WDSDM
FF FF2Ah
Watchdog Service
Data Match Register