Kenwood TS-2000 Manuale Istruttivo
5
2 YOUR FIRST QSO (HF/ 50 MHz band)
TRANSMITTING
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
.
DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT
PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH
HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
C
CALL
C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY
NAR
REV
MIC
PWR
KEY
LSB
USB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz
CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUA
L
RF
AF
SQL
SUB
CH
MULTI
BC
MAIN
GAIN
VFO/CH
MENU
TF-
SET
MAIN
SUB
SG.SEL
SCAN
M VFO
M.IN
RIT
CW TUNE
9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_
+
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA
TL
A/B
VFO/M
SPLIT
A=B
4 9
7
1
8
5
3
2
q
Turn the Tuning control to tune in a desired
station or to select an unused frequency.
station or to select an unused frequency.
w
Press [AT/ ANT1/2] momentarily.
•
“AT
” appears.
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC
e
Press and hold [AT/ ANT1/2] to activate the built-
in antenna tuner.
in antenna tuner.
•
“AT
” starts blinking and the MAIN band LED
above the [MIC/ CAR] key turns red.
FILTER
S
1
3
5
7
9
20
40
60dB
PWR
10
25
50
100W
ALC
•
Tuning should be completed in under
20 seconds, then “AT
20 seconds, then “AT
” stops blinking.
•
If tuning is not completed within 20 seconds,
error beeps sound. Press [AT/ ANT1/2] to stop
the error beeps and quit tuning. Check your
antenna system before continuing. If you do
not press [AT/ ANT1/2], tuning will continue for
approximately 60 seconds.
error beeps sound. Press [AT/ ANT1/2] to stop
the error beeps and quit tuning. Check your
antenna system before continuing. If you do
not press [AT/ ANT1/2], tuning will continue for
approximately 60 seconds.
Note: You will hear a lot of clicking sounds coming from the
transceiver while the antenna tuner is trying to tune the antenna.
This is simply the relay switches turning ON and OFF.
transceiver while the antenna tuner is trying to tune the antenna.
This is simply the relay switches turning ON and OFF.
r
With LSB, USB, or AM selected, press
[MIC/ CAR] to activate the Microphone Gain
Adjust.
[MIC/ CAR] to activate the Microphone Gain
Adjust.
•
“MIC GAIN 50” appears.
•
With FM selected, skip this step.
t
Press [SEND].
•
The MAIN band LED turns red.
y
Begin speaking into the microphone in your
normal tone of voice.
normal tone of voice.
u
LSB/ USB: While speaking into the microphone,
adjust the MULTI/ CH control so that the ALC
meter reflects according to your voice level.
adjust the MULTI/ CH control so that the ALC
meter reflects according to your voice level.
PWR
10
25
50
100W
FILTER
S
1
3
5
7
9
20
40
60dB
ALC
AM: While speaking into the microphone, adjust
the MULTI/ CH control so that the calibrated
power meter slightly reflects to your voice level.
the MULTI/ CH control so that the calibrated
power meter slightly reflects to your voice level.
FM: Skip this step.
i
When you finish speaking, press [SEND] to return
to receive mode.
to receive mode.
o
Press [MIC/ CAR] to quit the Microphone Gain
Adjustment.
Adjustment.
Note: If desired, access Menu No. 41 {page 28} to try the
Microphone Gain Adjust for FM.
Microphone Gain Adjust for FM.
This completes your introduction to the
TS-2000(X), but there is a great deal more to know.
“OPERATING BASICS” {page 18} and the following
chapters explain all the functions of this transceiver,
starting with the most basic, commonly-used
functions.
TS-2000(X), but there is a great deal more to know.
“OPERATING BASICS” {page 18} and the following
chapters explain all the functions of this transceiver,
starting with the most basic, commonly-used
functions.