Kenwood TS-2000 Manuale Istruttivo
10
4 GETTING ACQUAINTED
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
.
DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT
PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH
HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
C
CALL
C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY
NAR
REV
MIC
PWR
KEY
LSB
USB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz
CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUAL
RF
AF
SQL
SUB
CH
MULTI
BC
MAIN
GAIN
VFO/CH
MENU
TF-
SET
MAIN
SUB
SG.SEL
SCAN
M VFO
M.IN
RIT
CW TUNE
9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_
+
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA
TL
A/B
VFO/M
SPLIT
A=B
25
19
27
28
33
20
29
21
22
23
24
26
30
32
31
!9
LSB/ USB/ AUTO key
Press to select lower sideband (LSB) or upper
sideband (USB) mode for voice or digital operation.
Press [FUNC], [LSB/ USB/ AUTO] to toggle the auto
mode selection {page 73}.
sideband (USB) mode for voice or digital operation.
Press [FUNC], [LSB/ USB/ AUTO] to toggle the auto
mode selection {page 73}.
@0
CW/ FSK/ REV key
Press to select CW or FSK (Frequency Shift Keying)
mode {pages 30, 51}. Press [FUNC],
[CW/ FSK/ REV] to reverse the sideband pitch.
mode {pages 30, 51}. Press [FUNC],
[CW/ FSK/ REV] to reverse the sideband pitch.
@1
FM/ AM/ NAR key
Press to select FM or AM mode {pages 28, 29}.
Press [FUNC], [FM/ AM/ NAR] to select narrow
bandwidth transmission mode {page 29}.
Press [FUNC], [FM/ AM/ NAR] to select narrow
bandwidth transmission mode {page 29}.
@2
CLR key
Press to exit from, abort, or reset various functions.
Also used to erase memory channels {page 62} or
locking out memory channels from the scan list
{page 62}.
Also used to erase memory channels {page 62} or
locking out memory channels from the scan list
{page 62}.
@3
DISP key
Press to toggle the normal operating mode and DSP
filter setting display mode {page 55}. Press and hold
to start the Visual Scan function {page 70}.
filter setting display mode {page 55}. Press and hold
to start the Visual Scan function {page 70}.
@4
1MHz/ SEL key
Press to switch the MHz Up/ Down function ON or
OFF using the MULTI/ CH control. Press [FUNC],
[1MHz/ SEL] to change the increment/ decrement
step value {page 37}. Press and hold to start the
MHz Scan function {page 68}.
OFF using the MULTI/ CH control. Press [FUNC],
[1MHz/ SEL] to change the increment/ decrement
step value {page 37}. Press and hold to start the
MHz Scan function {page 68}.
@5
Tuning control
Turn to select the desired frequency {page 37}. Use
the convenient finger-tip cavity for continuous tuning.
the convenient finger-tip cavity for continuous tuning.
The lever behind this control adjusts the control
torque level; turn fully clockwise for light torque or
fully counterclockwise for heavy torque.
torque level; turn fully clockwise for light torque or
fully counterclockwise for heavy torque.
@6
CTRL key
Press to toggle the operating controls between the
main transceiver and the sub-receiver. The
transmission band is not affected by this key.
main transceiver and the sub-receiver. The
transmission band is not affected by this key.
@7
MENU key
Press to select or cancel the Menu mode that is used
for activating and configuring functions {page 21}.
for activating and configuring functions {page 21}.
@8
TF-SET key
While operating split-frequency, press to monitor or
change your transmit frequency {page 31}.
change your transmit frequency {page 31}.
@9
+/ – (Up/ Down) keys
Press to step through all the Amateur radio bands
consecutively {page 18}. Also used to make
selections from the Menu {page 21}, and to check the
Start and End frequencies of the Scan function
{page 62}.
consecutively {page 18}. Also used to make
selections from the Menu {page 21}, and to check the
Start and End frequencies of the Scan function
{page 62}.
#0
MAIN key
Press to transfer the operating controls to the MAIN
transceiver. Also moves the transmission band to the
main transceiver frequency.
transceiver. Also moves the transmission band to the
main transceiver frequency.
#1
SUB key
Press to transfer the operating controls to the sub-
receiver. Also moves the transmission band to the
sub-receiver frequency.
receiver. Also moves the transmission band to the
sub-receiver frequency.
#2
SCAN/ SG.SEL key
Press to start or stop the Scan function {page 66}.
Press [FUNC], [SCAN/ SG.SEL] to select a scan
group {page 69}.
Press [FUNC], [SCAN/ SG.SEL] to select a scan
group {page 69}.
#3
CALL/ C.IN key
Press to recall a call channel for the selected operating
band (HF/ 50 MHz/ 144 MHz/ 430 (440) MHz/ 1.2 GHz
(TS-2000/ TS-B2000 Optional)). Press [FUNC],
[CALL/ C.IN] to write a new Call Channel to the
memory {page 75}.
band (HF/ 50 MHz/ 144 MHz/ 430 (440) MHz/ 1.2 GHz
(TS-2000/ TS-B2000 Optional)). Press [FUNC],
[CALL/ C.IN] to write a new Call Channel to the
memory {page 75}.