Jack Lalanne's Power Juicer Power Juicer Express Manuale Proprietario
Activating Pin
(Bottom of pulp collector)
Juice Spout
Chute
Lid with built-in
Pulp Guard
Pusher
Pulp
Collector
Pulp
Collector
Lid with built-in
Pulp guard
Base
Filter/Blade
Receptacle
6
7
ASSEMBLY
ASSEMBLY
(CONT.)
STEP 2:
Align grooves on the bottom of pulp collector
with tracks on the base. Note: The Safety
MicroSwitch is located in the back center of
the base.
with tracks on the base. Note: The Safety
MicroSwitch is located in the back center of
the base.
Slide pulp collector with Activating
Pin towards base in the direction of arrows.
Make sure the pulp
collector is firmly in
place against base.
Make sure the pulp
collector is firmly in
place against base.
STEP 3:
Place receptacle on the base, with juicer
spout facing direction of locking bar.
Settle receptacle into alignment.
spout facing direction of locking bar.
Settle receptacle into alignment.
STEP 4:
Place filter/blade inside receptacle. Rotate
the filter/blade allowing it to settle into
alignment. Press down on rim of filter/blade
firmly to secure.
IMPORTANT:
the filter/blade allowing it to settle into
alignment. Press down on rim of filter/blade
firmly to secure.
IMPORTANT:
The unit will not start until
filter/blade is secure and firmly in place.
The motor will not
start until the unit is
properly assembled.
The motor will not
start until the unit is
properly assembled.
STEP 5:
Place lid with built-in pulp guard on top
of receptacle, making certain it is securely
aligned with the pulp guard facing in the
opposite direction of juice spout. Lock lid into
place by lifting locking bar up until it clicks
into grooves located on both sides of the lid.
Make sure locking bar is in the full upright,
locked position.
IMPORTANT:
of receptacle, making certain it is securely
aligned with the pulp guard facing in the
opposite direction of juice spout. Lock lid into
place by lifting locking bar up until it clicks
into grooves located on both sides of the lid.
Make sure locking bar is in the full upright,
locked position.
IMPORTANT:
The unit will not start until this
bar is properly locked in place and the pulp
collector is properly assembled.
collector is properly assembled.
STEP 7:
Insert pusher into chute. Always use pusher
to feed fruits and vegetables into unit. Push
gently, never force. The blade will do the work.
to feed fruits and vegetables into unit. Push
gently, never force. The blade will do the work.
STEP 6:
Make sure juice spout is in the downward
position. If the juice spout is left in the upright
position the juice will not flow. It will stay in the
receptacle and may overflow from the sides.
position. If the juice spout is left in the upright
position the juice will not flow. It will stay in the
receptacle and may overflow from the sides.
4
5
7
2
3
1
Assemble as shown
Locking
Bar
Receptacle
Locking
Bar
Front of Machine
(Spout side)
Receptacle
Top
Rim
Base
Juice
Spout
6
Base
Base
Base
(Tracks)
Pulp Collector
(Bottom)
DOWNWARD POSITION
UPRIGHT POSITION
Juice Spout
Safety MicroSwitch
IMPORTANT:
The motor will not run if
pulp collector is not properly assembled.
The motor will not run if
pulp collector is not properly assembled.
STEP 1:
Place base on a dry flat surface with locking
bar in down position as shown. In front of the
machine (spout side).
IMPORTANT:
bar in down position as shown. In front of the
machine (spout side).
IMPORTANT:
There is a Safety MicroSwitch
located in the back center of the base. This
mechanism is an added safety feature. Once
the pulp collector is in place the Activating Pin
on the bottom of the pulp collector activates
the Safety MicroSwitch. This will
protect you from accidentally
putting hands or fingers under
the machine while the blade is
turning. Once the pulp collector
is removed from the main base
the motor will not run.
mechanism is an added safety feature. Once
the pulp collector is in place the Activating Pin
on the bottom of the pulp collector activates
the Safety MicroSwitch. This will
protect you from accidentally
putting hands or fingers under
the machine while the blade is
turning. Once the pulp collector
is removed from the main base
the motor will not run.