Magikitch'n MKG72 Manuale Utente
Operations
MKG Series Gas Griddle
L25-052 Rev. 0 (5/06)
9
LEFT PIEZO IGNITOR
RIGHT PIEZO IGNITOR
LEFT PILOT BUTTON
RIGHT PILOT BUTTON
PILOT HOLES
METHOD
A
PILOT READY LIGHT(S)
PILOT HOLES
METHOD
B
ON/OFF(I/O) SWITCH
2. Operation Section
Ensure that a proper installation has been performed on the appliance and that all warnings, cautions, and
notices contained in this manual have been read, understood and adhered to before proceeding.
notices contained in this manual have been read, understood and adhered to before proceeding.
2.1. Lighting
Instructions
2.1.1. Snap-Action
Thermostat
Appliances
1. Turn all thermostat knobs to the “OFF”
position.
2. Open front door of the griddle, turn the
manual gas shut off valve to the “ON”
position, see Figure 6.
position, see Figure 6.
3. Press and hold the left or right RED pilot
button, see detail Method A at right, and
light the left or right pilot by depressing the
Piezo ignition control, look through the
pilot hole to see the pilot ignites. With pilot burning, keep the RED pilot knob depressed for 45 seconds or
until pilot remains lit automatically. If the Piezo ignition control does not light the pilot(s), a flame source
can be used to light the pilot(s) through the pilot holes provided in the front panel of the appliance.
light the left or right pilot by depressing the
Piezo ignition control, look through the
pilot hole to see the pilot ignites. With pilot burning, keep the RED pilot knob depressed for 45 seconds or
until pilot remains lit automatically. If the Piezo ignition control does not light the pilot(s), a flame source
can be used to light the pilot(s) through the pilot holes provided in the front panel of the appliance.
4. Repeat steps 1,2, and 3 for all remaining pilots.
5. Operate thermostats by turning knobs clockwise to the desired temperature and insure that burners light
5. Operate thermostats by turning knobs clockwise to the desired temperature and insure that burners light
properly by looking through the pilot holes provided in the front panel.
2.1.2. Solid State And Electric Thermostat Appliances
1. Turn all thermostat knobs to the “OFF” position, or the lowest possible temperature setting.
2. Turn the Manual gas shut off valve to the "ON" position, this valve is located at the rear of the unit, see
2. Turn the Manual gas shut off valve to the "ON" position, this valve is located at the rear of the unit, see
Figure 6.
3. Turn
the
RED "I/O" switch to the “ I ” (ON)
position for all desired Thermostats to be
operated, See detail Method B at right. When
the Pilot ready (Amber) light illuminates, the
pilot(s) are ready to operate the main
burners.
operated, See detail Method B at right. When
the Pilot ready (Amber) light illuminates, the
pilot(s) are ready to operate the main
burners.
4. Repeat steps 1,2, and 3 for all thermostat
controls to be operated.
5. Operate thermostats by turning knobs
clockwise to the desired temperature and
insure that burners light properly by looking
through the pilot holes provided in the front
panel. The RED "I/O" switch will illuminate
when the thermostat calls for heat.
insure that burners light properly by looking
through the pilot holes provided in the front
panel. The RED "I/O" switch will illuminate
when the thermostat calls for heat.
CAUTION
If Pilot Ready light(s) does not illuminate, Turn all Thermostat "I/O" switches for that
pilot to “O”(OFF), wait five minutes before attempting to re-light.
If Pilot(s) extinguish or gas supply is interrupted, turn thermostat knobs and the gas shut off valve to
the "OFF" position and wait 5 minutes before attempting to re-light.