LUCE PT-L6510E Manuale Utente
31
ENGLISH
TV-SYSTEM
(for composite/S-video only)
AUTO1: Automatically selects the TV standard that
matches the input video signal, out of NTSC,
PAL, NTSC4.43, and SECAM.
PAL, NTSC4.43, and SECAM.
AUTO2: Automatically selects the TV standard that
matches the input video signal, out of NTSC,
PAL-M, and PAL-N.
PAL-M, and PAL-N.
• Normally “AUTO1” or “AUTO2” should be chosen for
this option.
• If input video signal quality is poor, choose the TV
system that matches the input video signal.
Automatically selected by detecting the horizontal/vertical
scan frequencies and colour sub-carrier listed in the table
below:
SIGNAL MODE
(for RGB/YP
B
P
R
/DVI signals only)
“SIGNAL MODE” displays the names of the signals
(resolution) presently applied to the RGB or YP
(resolution) presently applied to the RGB or YP
B
P
R
input ports. For details of signal names, see the table
on page 48.
If the user mode is registered, the following menu
will appear. You can choose either “AUTO” or a
registered user setting from “USER1” to “USER3” with
the
on page 48.
If the user mode is registered, the following menu
will appear. You can choose either “AUTO” or a
registered user setting from “USER1” to “USER3” with
the
or
buttons.
If “AUTO” is chosen, a setting closest to the user
setting is automatically selected. (In the example
above, only “USER1” is registered for user address.)
setting is automatically selected. (In the example
above, only “USER1” is registered for user address.)
W.BAL (White balance) R/G/B
(for RGB/DVI signals only)
White balance may be adjusted for each colour to
correct reddish or bluish tones in white portions of
the picture:
White balance may be adjusted for each colour to
correct reddish or bluish tones in white portions of
the picture:
button: Deepens the selected colour.
button: Weakens the selected colour.
button: Weakens the selected colour.
Note
• Separate sets of adjustment parameters can
be saved for the RGB1, RGB2 and DVI inputs.
TV-SYSTEM
AUTO1
AUTO2
NTSC
NTSC4.43
PAL
PAL-M
PAL-N
SECAM
T a b l e
H . S c a n
F r e q u e n c y
( k H z )
V . S c a n
F r e q u e n c y
( H z )
C o l o u r
S u b c a r r i e r
( M H z )
N T S C
N T S C 4 . 4 3
P A L
P A L - M
P A L - N
S E C A M
1 5 . 7 5
1 5 . 7 5
1 5 . 6 3
1 5 . 7 5
1 5 . 6 3
1 5 . 6 3
6 0 . 0 0
6 0 . 0 0
5 0 . 0 0
6 0 . 0 0
5 0 . 0 0
5 0 . 0 0
3 . 5 8
4 . 4 3
3 . 5 8
4 . 2 5 o r 4 . 4 1
STANDARD
Pressing the “ENTER” button resets all the
adjustment parameter values to the factory default
values, with a “STANDARD” indicator shown on the
upper right corner of the menu.
adjustment parameter values to the factory default
values, with a “STANDARD” indicator shown on the
upper right corner of the menu.
SIGNAL MODE
AUTO
USER1
Note
• If you choose a user address registered for a
signal that does not match the input signal, it is
regarded as “no signal”, and the projector will
display the specified background colour.