Land Pride Saw PR1560 Manuale Utente
9
Section 1: Assembly and Set-Up
PR1560 & PR1572 Powered Rakes 314-164M
Land Pride
7/14/08
Tractor Requirements
The Powered Rake is designed with a category 1, 3-point
hitch and will fit a Land Pride Cat. 1 Quick-Hitch. The
maximum horsepower rating for the tractor is 45 HP
depending on lift capacity and field conditions. Front
tractor weights and/or ballast to tires may be required to
offset weight of unit. Consult your tractor manual for
details.
hitch and will fit a Land Pride Cat. 1 Quick-Hitch. The
maximum horsepower rating for the tractor is 45 HP
depending on lift capacity and field conditions. Front
tractor weights and/or ballast to tires may be required to
offset weight of unit. Consult your tractor manual for
details.
Gauge Wheel Assembly (PR1572)
Refer to Figure 1-1:
PR1572 is shown. On the PR1560 the gauge wheel arms
are part of the frame.
are part of the frame.
1.
Install the gauge wheels (#1) to the frame with the u-
bolts (#2) lock washers (#3) and nuts (#4) as shown.
bolts (#2) lock washers (#3) and nuts (#4) as shown.
Gauge Wheel
Figure 1-1
Tractor Hook-Up
!
CAUTION
Do not stand between the tractor and implement during
hook-up.
hook-up.
1.
Be certain that the tractor draw bar will not interfere.
Move draw bar ahead or remove if required. Draw bar
should also be checked for clearance when unit is
being raised for the first time.
Move draw bar ahead or remove if required. Draw bar
should also be checked for clearance when unit is
being raised for the first time.
2.
Align lower link arms of tractor to hitch lugs on
Powered Rake. Insert lower hitch pins into lower ball
swivels and attach linch pins.
Powered Rake. Insert lower hitch pins into lower ball
swivels and attach linch pins.
3.
Attach tractor top link to upper hitch of Powered
Rake. Secure with pin.
Rake. Secure with pin.
4.
Connect hydraulic hoses on Powered Rake to the
tractor.
tractor.
18602
!
WARNING
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be surgically
removed within a few hours by a doctor or gangrene may result.
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be surgically
removed within a few hours by a doctor or gangrene may result.
Driveline Installation
1.
Slide the driveline over the splined shaft at the front
of the Powered Rake and secure with the locking
device of driveline.
of the Powered Rake and secure with the locking
device of driveline.
2.
Slide the driveline over the tractor’s splined PTO
shaft and secure with the locking device of driveline.
shaft and secure with the locking device of driveline.
3.
Hook the safety chain on the driveline Powered Rake
end around a tube on the front of the Powered Rake
to prevent the shield from rotating.
end around a tube on the front of the Powered Rake
to prevent the shield from rotating.
4.
The driveline should now be moved back and forth to
insure that it is secure on the PTO shaft of the tractor
and Powered Rake drive shaft.
insure that it is secure on the PTO shaft of the tractor
and Powered Rake drive shaft.
5.
Should the driveline require shortening:
a.
Hold the half-shafts next to each other in the
shortest working position and mark them.
shortest working position and mark them.
b.
Shorten inner and outer guard tubes equally.
c.
Shorten inner and outer sliding profiles by the
same length as the guard tubes.
same length as the guard tubes.
d.
Proper overlap is a minimum of one-half the
length of each tube, with both tubes being of equal
length.
length of each tube, with both tubes being of equal
length.
e.
Round off all sharp edges and remove burrs.
Grease sliding profiles.
Grease sliding profiles.
Prior to initial operation and after long periods of
inactivity, the Friction Clutch should be “run-in”. Refer to
Figure 1-2.
inactivity, the Friction Clutch should be “run-in”. Refer to
Figure 1-2.
1.
Tighten all 4 nuts uniformly until the spring load is low
enough that the clutch slips freely with the PTO
engaged.
enough that the clutch slips freely with the PTO
engaged.
2.
Turn nuts fully back. Clutch is ready for use.
Friction Clutch “Run In”
Figure 1-2
IMPORTANT: The inner shield half attaches to the
Powered Rake.
Powered Rake.
10103
Section 1: Assembly and Set-Up