CyberPower CPS140BI Dépliant
Output Power
140 Watts Continuous
Output Voltage
120 Volts +/- 10%
Output Frequency
60 Hz
Output Waveform
Simulated Sine Wave
Input Voltage
10.8 to 15.8 volts
Low Voltage Shutdown
10.5 volt
Problem
Possible Cause
Suggested Solutions
No AC output power
(Power indicator is not
illuminated)
(Power indicator is not
illuminated)
Poor contact with lighter socket
Automotive electrical systems
requires ignition to be on.
requires ignition to be on.
Car s lighter socket fuse blown
Over-heating
Vehicle s battery below 10.8
volts.
volts.
Ensure the inverter adapter is securely
plugged into vehicle s lighter socket.
Replace the lighter socket if necessary.
plugged into vehicle s lighter socket.
Replace the lighter socket if necessary.
Turn the vehicle ignition key to the
Accessory
position.
Check the vehicle fuse panel and replace
the damaged fuse.
the damaged fuse.
Allow inverter to cool down. Ensure that
there is adequate ventilation around the
unit and load is no more than 140 watts for
continuous operation.
there is adequate ventilation around the
unit and load is no more than 140 watts for
continuous operation.
Unplug the inverter and charge the vehicle
battery.
battery.
Short/Long Beep
Your vehicle s battery input
voltage is below than 10.8 volt.
voltage is below than 10.8 volt.
Vehicle s battery input voltage
is higher than 15.8 volt.
is higher than 15.8 volt.
Inverter is overload.
Check vehicle s battery and ensure its
capacity. Change vehicle s battery if
necessary.
capacity. Change vehicle s battery if
necessary.
Check for your vehicle s battery
manufacturer guideline.
manufacturer guideline.
Reduce load to 140 watts max to maintain
regulation.
regulation.
Contact Screw
Spring
Contact Pin
Fuse
Decorative Ring
Lighter Adapter
CPS140BI contains a fuse inside in the Lighter Adapter (see Figure 2) to protect the unit against
overloading. If the inverter draws more than 140 watts, the internal fuse may be blown to protect
the inverter, vehicle battery and the connected equipment. To replace the fuse, please follow the
instruction below:
overloading. If the inverter draws more than 140 watts, the internal fuse may be blown to protect
the inverter, vehicle battery and the connected equipment. To replace the fuse, please follow the
instruction below:
1. Unplug the inverter from the power source.
2. Remove the Contact Screw from the Lighter Adapter.
3. Replace the 15 ampere fuse.
4. Reassemble the fuse, contact pin and contact screw carefully.
5. Ensure all pieces showed in Figure 2 are installed in the sequence shown.
2. Remove the Contact Screw from the Lighter Adapter.
3. Replace the 15 ampere fuse.
4. Reassemble the fuse, contact pin and contact screw carefully.
5. Ensure all pieces showed in Figure 2 are installed in the sequence shown.
*Note: For in-warranty units, the replacement fuse can be obtained from CyberPower
Technical Support. For out-of-warranty units, the replacement 15 ampere fuse can be obtained
from most electronic supply retailers.
from most electronic supply retailers.
WARRANTY RETURN
Cyber Power Systems, Inc.
5555 12th Avenue East, Suite 110, Shakopee, MN 55379, U.S.A.
5555 12th Avenue East, Suite 110, Shakopee, MN 55379, U.S.A.
TEL: (952) 403-9500
FAX: (952) 403-0009
Toll-Free: (877) 297-6937
E-mail:
sales@cyberpowersystems.com
Web:
www.cyberpowersystems.com
Entire contents copyright
2004 Cyber Power Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited
K01-BT14000
C
2004-5-075/back K