Creek Audio OBH 18 Dépliant
INPUT AND OUTPUT CONNECTION
WIRING THE OBH 18
The output from the turntable is normally terminated on two
'Phono' plugs or RCA jacks. The level is dependent on the type of
cartridge used, and in the case of moving magnet will normally be
around 2 - 5 milli Volts and for moving coil - 200 - 500 micro Volts.
'Phono' plugs or RCA jacks. The level is dependent on the type of
cartridge used, and in the case of moving magnet will normally be
around 2 - 5 milli Volts and for moving coil - 200 - 500 micro Volts.
Most MM cartridges will be properly matched by using the OBH 18.
By plugging the signal leads from your turntable into the OBH 18
input, the signal will be boosted to 'LINE' level at its output. To
prevent hum pick-up, it may be necessary to join the turntable's
earth lead to the OBH 18 ground terminal.
By plugging the signal leads from your turntable into the OBH 18
input, the signal will be boosted to 'LINE' level at its output. To
prevent hum pick-up, it may be necessary to join the turntable's
earth lead to the OBH 18 ground terminal.
The output from the OBH 18 can be connected to most integrated
amplifier’s and pre-amplifier's line inputs via a regular Phono to
Phono (RCA to RCA) stereo interconnect lead.
amplifier’s and pre-amplifier's line inputs via a regular Phono to
Phono (RCA to RCA) stereo interconnect lead.
The output impedance of the OBH 18 is <100 W, therefore it can be used
to drive long interconnects without loss, provided they are high
capacitance types.
to drive long interconnects without loss, provided they are high
capacitance types.
Connect the OBH 18 to the input of your amplifier with a stereo
POWER SUPPLY REQUIREMENTS
RCA inter-connect cable. If using a Creek integrated amplifier
In common with all electrical appliances, the OBH 18 requires a
connect to the first input.
power supply.
The connection for the phono output from the turntable plus
The requirement for the OBH 18 is for 24 Volts DC at 30 milli-Amps
ground is clearly marked on the rear panel.
current, minimum. A custom Creek power supply (Creek-Uni) has
been provided and this must be connected via the DC inlet on the
been provided and this must be connected via the DC inlet on the
The power supply is connected to the 2.1mm positive pin power
rear panel of the OBH 18.
jack and then to the wall socket. The OBH 15 should be placed
away from power supply hum fields for the lowest noise operation.
away from power supply hum fields for the lowest noise operation.
The power supply which has been provided is a
NOTE
Due to the inherent muting circuitry in the OBH 18, the signal will
take a few seconds to be heard after the power is switched on.
Due to the inherent muting circuitry in the OBH 18, the signal will
take a few seconds to be heard after the power is switched on.
It is necessary for the OBH 15 to be ‘burned in’ for at least 24 hours
before its full sound quality potential can be realised.
before its full sound quality potential can be realised.
The on/off switch is located on the rear panel. As the OBH 18 draws
very little power it may be left switched on permanently.
very little power it may be left switched on permanently.
switchable supply
with a universal input range of 100 – 240 Volts. The Creek-Uni
power supply is supplied with a pack of universal plug fittings to
adapt for Europe, U.K. and the Far-east, USA and Australia.
Choose the correct fitting for your country of use and simply snap
in place.
power supply is supplied with a pack of universal plug fittings to
adapt for Europe, U.K. and the Far-east, USA and Australia.
Choose the correct fitting for your country of use and simply snap
in place.