Futaba 10CAG Manuale Istruttivo
48
TRIM
submenu: resets and adjust effectiveness of digital trims.
The 10CG has digital trims which are different from conventional mechanical
trim sliders. Each TRIM LEVER is actually a two-directional switch. Each time
the TRIM LEVER is pressed, the trim is changed a selected amount. When you
hold the TRIM LEVER, the trim speed increases. The current trim position is
graphically displayed on the start up screen. The TRIM submenu includes two
functions that are used to manage the trim options.
trim sliders. Each TRIM LEVER is actually a two-directional switch. Each time
the TRIM LEVER is pressed, the trim is changed a selected amount. When you
hold the TRIM LEVER, the trim speed increases. The current trim position is
graphically displayed on the start up screen. The TRIM submenu includes two
functions that are used to manage the trim options.
HELI
models only: OFFSET is available in the idle ups. If OFFSET is inhibited, adjustment of the TRIM LEVERS will adjust
WKHWULPVIRUDOOÀLJKWFRQGLWLRQV,IOFFSET is active, then moving the trims within any one condition will effect only that
condition. See OFFSET, p. 102.
condition. See OFFSET, p. 102.
Trim reset (RESET): electronically centers the trims to their default values. Note that the SUB-TRIM settings and the trim
STEP
STEP
rate are not reset by this command.
GOAL of EXAMPLE:
STEPS:
INPUTS:
Reset trims to neutral after having
adjusted all linkages.
N O T E : T h i s i s o n e o f s e v e r a l
functions for which the radio requires
FRQ¿UPDWLRQWRPDNHDFKDQJH
adjusted all linkages.
N O T E : T h i s i s o n e o f s e v e r a l
functions for which the radio requires
FRQ¿UPDWLRQWRPDNHDFKDQJH
Open BASICmenu, then open TRIM
submenu.
submenu.
for 1 second.
(If ADVANCE,
again.)
C
to TRIM.
Request
DQGFRQ¿UPWKHUHVHW.
for 1 second.
Beep sounds.
Close.
Where next?
Adjust SUB-TRIMs: see p. 49.
Adjust trim rate (STEP): see below.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Adjust trim rate (STEP): see below.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Trim step (STEP): changes the rate at which the trim moves when the TRIM LEVER is activated. It may be set from 1 to
40 units, depending on the characteristics of the aircraft. Most ordinary aircraft do well at about 2 to 10 units. Generally
ODUJHUWULPVWHSVDUHIRUPRGHOVZLWKODUJHFRQWUROWKURZVRUIRU¿UVWÀLJKWVWRHQVXUHVXI¿FLHQWWULPWRSURSHUO\FRUUHFWWKH
PRGHO6PDOOHUWULPVWHSVDUHODWHUXVHGWRDOORZYHU\¿QHDGMXVWPHQWVLQÀLJKW
40 units, depending on the characteristics of the aircraft. Most ordinary aircraft do well at about 2 to 10 units. Generally
ODUJHUWULPVWHSVDUHIRUPRGHOVZLWKODUJHFRQWUROWKURZVRUIRU¿UVWÀLJKWVWRHQVXUHVXI¿FLHQWWULPWRSURSHUO\FRUUHFWWKH
PRGHO6PDOOHUWULPVWHSVDUHODWHUXVHGWRDOORZYHU\¿QHDGMXVWPHQWVLQÀLJKW
GOAL of EXAMPLE:
STEPS:
INPUTS:
Double the sensitivity (larger step) of
the AILERON TRIM LEVERS for
a first flight of an aerobatic model to
HQVXUHVXI¿FLHQWUDQJHWRWULPWKHPRGHO
IRUOHYHOÀLJKW
the AILERON TRIM LEVERS for
a first flight of an aerobatic model to
HQVXUHVXI¿FLHQWUDQJHWRWULPWKHPRGHO
IRUOHYHOÀLJKW
Open TRIM submenu and choose the
STEP
STEP
you wish to change. (Ex: aileron)
for 1 second.
(If ADVANCE,
again.)
C
to TRIM.
Adjust the size of the step.
(Ex: incr. to 8)
(Ex: incr. to 8)
C
to AILE.
to 8.
Repeat as desired for other channels.
C
to ELEV.
to new setting.
Repeat as needed.
Close.
Where next?
Adjust sub trims: see p. 49.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.
Adjust END POINTs: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO D/R,EXP): see p. 42.