Manualsbrain.com
  1. Manuali
  2. Marche
  3. Futaba
  4. 10CAG
  5. Manuale Istruttivo

Futaba 10CAG Manuale Istruttivo

Scarica
Pagina di 119
90
GETTING STARTED WITH A BASIC HELICOPTER 
This guideline is intended to help you set up a basic (H-1) heli, to get acquainted with the radio, to give you a jump start on 
using your new radio, and to give you some ideas and direction on how to do even more with this powerful system than 
you may have already considered. It follows our basic format of all programming pages—a big picture overview of what 
we're trying to accomplish; a “by name” description of the steps to help acquaint you with the radio; and then a step-by-
step instruction to leave out the mystery and challenge of setting up your model. 
%ULHÀ\WKHW\SLFDOKHOLFRSWHU¶VFRQWUROVDUHDVIROORZV
• Aileron: changes cyclic lateral (roll) . Rolls the helicopter. Tilts the swashplate to the left or right. CH1. 
• Elevator: changes cyclic pitch. Changes the helicopter’s angle of attack (nose up or nose down). Tilts the entire 
swashplate fore and aft. CH2.
• Rudder: changes the angle of the tail rotor. Yaws the helicopter left or right. CH4. 
• Collective Pitch: adjusts main rotor collective [angle of the paddles], changing the main blades’ pitch. Increased 
collective pitch (with throttle) causes the helicopter to rise. Moves in conjunction with throttle on the THROTTLE 
STICK. CH6. 
• Throttle:
RSHQVFORVHVFDUEXUHWRU0RYHVLQFRQMXQFWLRQZLWKFROOHFWLYHSLWFKRQWKHTHROTTLE STICK. CH3. 
• REVO: mix that adds rudder in conjunction with pitch. This helps compensate for rotation of the helicopter caused by the 
LQFUHDVHGHQJLQHWRUTXH 1HYHUXVHUHYRPL[LQJZLWKDKHDGLQJKROG$9&6J\URWKHJ\URDOUHDG\GRHVWKLV 
)RUDGGLWLRQDOGHWDLOVVHHWKDWIXQFWLRQ VVHFWLRQLQWKLVPDQXDO²WKHSDJHQXPEHUVDUHLQGLFDWHGLQWKH¿UVWFROXPQIRU\RX
GOAL of EXAMPLE:
STEPS:
INPUTS:
Prepare your helicopter.
Install all servos, switches, receiver per your model's instructions. Set all trims, 
dials and sliders to neutral.
&RQ¿UPDOOFRQWUROOLQNDJHVDUHGHJUHHV RUSHULQVWUXFWLRQV IURPWKHVHUYR
horn to the ball link for proper geometry and that no slop is present.
Mechanically adjust all linkages to get as close as possible to proper control 
throws and minimize binding prior to radio set up.
Select the proper MODEL TYPE for your 
model. Ex: HELI (H-1). See p. 93.
[ N O T E :   T h i s   i s   o n e   o f   s e v e r a l 
functions for which the radio requires 
confirmation to make a change. Only 
critical changes require additional key 
strokes to accept the change.]
(If the correct model type was already 
displayed, be sure to do a model reset to 
discard any unwanted settings.)
In the BASIC menu, open the PARAMETER 
submenu.
Turn on the transmitter.
for 1 second.
 (If ADVANCE,
again.)
then
C
to highlight PARAMETER.
to choose PARAMETER.
Go to MODEL TYPE.
C
to TYPE.
Select proper MODEL TYPE.
Ex:  HELI(H-1). Confirm the change. 
Close PARAMETER.
to HELICOPTER.
for 1 second.
Are you sure?
 displays. 
WRFRQ¿UP
C
to SWASH.
to H-1.
for 1 second.
Are you sure?
 displays. 
WRFRQ¿UP
to return to BASIC menu.
Then, NAME the model. P. 32.
(You do not need to do anything to 
“ save” or store this data.)
In the BASIC  menu, open the MODEL 
submenu.
C
as needed to highlight MODEL.
to choose MODEL.
Go to MODEL NAME.
C
to NAME.
(First character of model'sname is highlighted.)
Input aircraft's name.
Close the MODEL submenu when done.
WRFKDQJH¿UVWFKDUDFWHU
When proper character is displayed,
C
to move to next character. 
Repeat.
to return to BASIC menu.