American Standard Personal Lift 2403 Manuale Utente
7 3 0 1 1 2 3 - 1 0 0 R e v . D
6
7
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height
to size before installing caps.)
to size before installing caps.)
c. Smooth off the bead of sealant around base. Remove
excess sealant.
excess sealant.
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
!
- 2 -
8a
8b
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CONE WASHER WITH
PLASTIC SUPPLY LINE.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
washers already
included. No
additional washers
needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
NUT
COUPLING
NUT
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
COUPLING
NUT
NUT
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
CONE
WASHER
WASHER
EXISTING
CONE
WASHER
CONE
WASHER
EXISTING
WASHER
WASHER
With correct washers in place
(see Step 8a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
(see Step 8a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
BOLTS
CLOSET FLANGE
BOLT CAP
!
WARNING: Do not use plumber’s putty, pipe dope, or any other sealant on the water supply connection
to this tank. If the connection leaks after hand tightening, replace the supply line. If the connection
continues to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.
to this tank. If the connection leaks after hand tightening, replace the supply line. If the connection
continues to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.