Braun Personal Lift Corporation FMVSS No. 403 Manuale Utente

1/4-20 x 3/8" 

Hex Screws

Lock

Washer

Reinforcement

“L” Bracket

Cable-activated

Manual Release

(from lift)

7/8" Diameter 

Mounting Hole

Through-Floor

Cable and Hose 

Grommet

(3" Diameter 

Mounting Hole)

Note:
Remove
plug from 
vent tube.

Connect red positive 
(+) power cable here 
(from Circuit Sentry).

Connect harnesses to 
mating harnesses at 
pump (labeled).  Detailed 
installation instructions 
supplied with kits.

5/16"

External Tooth

Star Washer

9/32"

Diameter

Pilot Hole

Thread
Cutting

Screw

One ground cable is pump 
mounted.  Route this ground cable 
through the floor grommet and con-
nect to a vehicle framing member 
(see Figure L).

A ground cable (minimum 2 gauge) 
must be connected from vehicle 
battery negative post to the same 
vehicle framing member the pump 
ground cable is attached to.

Ground Cable Corrosion:
When mounting ground 
cables, remove undercoat-
ing, dirt, rust, etc. from 
framing member around 
mounting holes.  Apply
protective coating to mount-
ing holes to prevent corro-
sion. Failure to do so will 
void warranty of certain 
electrical components.

Route two main wiring 
harnesses from lift through 
floor grommet to pump 
module.  Connect to mat-
ing harnesses at pump.

5/16"

Lag Bolts

(typical - 4)

Note:  Seal the 
floor cable and 
hose grommet 
following installa-
tion procedures 
(fill with silicone).

Mount reinforcement “L” bracket 
to pump mounting bracket as 
shown in Figure K.  Secure 
pump mounting bracket to floor 
using four 5/16" lag bolts. 

Note:  Locate and drill pump 
module mounting holes, floor 
grommet 3" diameter hole and 
manual release 7/8" diameter 
hole before mounting pump. 

Cable-activated Manual 
Release: The T-handle must 
be mounted inside the vehicle.
The cable must operate freely 
(no kinks or bends). Warning
tag 81823 must remain attached 
to the handle.  Remove handle 
for installation.

Note: All
wiring harness 
connections
must be 
inside the 
vehicle.

The pump module is equipped 
with a lift interface 9-circuit 
connector (female socket).
A mating 9-circuit connector 
(male plug) is supplied.

To meet minimum
NHTSA requirements, 
connect to vehicle inter-
lock harness as outlined 
in Figure N (Steps 1-4). 

Universal Interlock Kit 
30940K is available 
for easy interface with 
vehicle OEM electronic 
signals.

Instrument Panel Display 
Kit 30938K provides an 
LED Panel Display that 
interfaces with Braun 
Universal Interlock Kit 
30940K.

Note:  Detailed installa-
tion instructions are sup-
plied with interlock kits.

Remove the plug 
from 1/4" diameter 
clear vent tube.
See Figure N.

Route hydraulic 
hose assembly 
through floor 
grommet to quick-
disconnect fitting at 
lift.  Connect hose.

Install Circuit 
Sentry as shown 
in Figure M.  At-
tach power cable 
and lead cable as 
detailed.

Install black jumper wire 
last.  Install the black jumper 
wire in pump Terminal Strip 
terminals 6 and 9 after all 
other electrical connections 
have been made (see Panel 
4). The jumper wire supplies 
power to the circuit board.
Check floor level and inner roll 
stop adjustments as detailed 
in Panel 4 before operating 
lift with electric pump.

Connect harness to mating har-
ness at pump module (labeled).
Mat must be installed on a flat 
rigid surface.  Inboard edge of mat 
must be minimum 18" from edge 
of finished floor or stepwell.