Bench 32PFL7582D Manuale Utente
9
GB/IE/CY
Safety instructions
specific to the tool
J
Check the condition of the device,
charger
11
, lead
12
and plug
13
before starting to charge the device.
Do not use the tool if any of the parts are dam-
aged. Never open the tool. Repair or replace-
ment must only be carried out by the Service
Office or an electrical expert. Damaged tools,
mains cables or mains plugs pose a danger to
life as a result of electric shock.
aged. Never open the tool. Repair or replace-
ment must only be carried out by the Service
Office or an electrical expert. Damaged tools,
mains cables or mains plugs pose a danger to
life as a result of electric shock.
J
Maintenance and cleaning must only be carried
out when the tool is switched off and the battery
charger is disconnected from the mains power.
out when the tool is switched off and the battery
charger is disconnected from the mains power.
J
Never under any circumstances charge the
integrated rechargeable battery with the bat-
tery charger if damaged.
integrated rechargeable battery with the bat-
tery charger if damaged.
J
Only use the original battery charger to
charge the integrated battery.
charge the integrated battery.
J
Before connecting the battery charger to the
mains power, make sure that the mains current
is 230 V ~ 50 Hz and is equipped with a 16 A
mains power, make sure that the mains current
is 230 V ~ 50 Hz and is equipped with a 16 A
fuse in accordance with requirements.
Caution! How to avoid injury:
J
Use the following safety gear when
operating the tool: Wear safety gog-
gles, worker safety boots and protec-
gles, worker safety boots and protec-
tive gloves.
J
Caution! The saw blade
7
runs on after the tool has
been switched off! Avoid any
been switched off! Avoid any
contact with the rotating saw blade
7
.
J
Only remove workpieces when the saw blade
has come to a complete standstill.
has come to a complete standstill.
J
Prevent the saw blade
7
from coming into
contact and / or colliding with stones, metal, or
similar materials. The saw blade
similar materials. The saw blade
7
may other-
wise be damaged.
J
Switch off the device immediately (by releasing
the On / Off switch
4
):
- If you strike any foreign body (e.g. a nail)
while making a cut!
- If the saw blade
7
becomes blocked (e.g.
by wood shavings / sawdust).
J
Never have the charger
11
connected to the
device while you are sawing.
J
Keep out of the area in which a cut and falling
branch could hit.
Q
Starting operation
Q
Charging the integrated
rechargeable battery
The battery initially requires about 4 - 5 charging
cycles before it achieves its maximum capacity.
cycles before it achieves its maximum capacity.
Starting the charging process
j
Insert the plug
13
into the charging socket
2
.
j
Insert the charger
11
into the mains socket.
The LED on the charger
11
indicates the device’s
battery charge state:
1.
1.
Red: The device requires to be charged or is
being charged.
being charged.
2.
Green: The device is fully charged.
Ending the charging process
j
Pull the charger
11
out of the mains socket.
j
Pull the plug
13
out of the charging socket
2
.
Only charge the rechargeable battery when it is
empty. This prevents the “memory effect” (loss of
capacity as a result of charging when only partially
discharged).
empty. This prevents the “memory effect” (loss of
capacity as a result of charging when only partially
discharged).
J
Never switch the device on while it is being
charged.
J
Do not allow any objects to cover the charger!
The heat generated by the charger while oper-
ating can lead to a build-up of heat!
ating can lead to a build-up of heat!
General safety advice / Starting operation