Wibur Curtis Company LIGD Dépliant
© 2001-2006 Wilbur Curtis Company, Inc.
Printed in U.S.A.
MAY/06 – 7829 – F-3122 – Rev A
Factory-set grind cycles can be easily changed.
Grind time for each cycle is accurately displayed by the read-
out. To change, simply follow these steps (each button is set
independently):
• Turn the grinder off. Place a brew cone and filter in the
out. To change, simply follow these steps (each button is set
independently):
• Turn the grinder off. Place a brew cone and filter in the
machine.
• Press and hold the grind cycle button. At the same time
press and release the ON/OFF button.
• Now press the grind cycle button again. The display will
indicate its current setting. Immediately following it will
begin grinding. The display will indicate the elapsed time
from zero.
begin grinding. The display will indicate the elapsed time
from zero.
• When the desired level is reached, release the button.*
• Wait until the motor has stopped completely, and press any
• Wait until the motor has stopped completely, and press any
OTHER button on the same side. This sets the time and
exits the programming mode.
exits the programming mode.
NOTE: *Add time by pressing and holding the flashing button until the
desired level is reached.
Digital InterLock
TM
System – Only from Curtis.
Automatic Grinder-to-Brewer Interface
Designed for fresh grind/fresh brew programs, the Curtis
Digital InterLock
Digital InterLock
TM
System connects compatible Digital
Control Coffee Brewers to Digital Control Grinder for simple,
error-proof grinding and brewing.
error-proof grinding and brewing.
With the push of a button, the Grinder automatically
conveys the selected grind volume to the brewing system.
The brew selection is then “locked-in” to the corresponding
grind cycle...incorrect cycles are “locked out.” If both brewer
sides are in use, the Grinder’s memory stores the information
and waits until a side is available.
grind cycle...incorrect cycles are “locked out.” If both brewer
sides are in use, the Grinder’s memory stores the information
and waits until a side is available.
Standard Features
•
Dual-Hoppers -
Include decaf or a specialty coffee in your
fresh grind/fresh brew program.
•
Infinitely Adjustable Grind Settings -
From extra coarse to
extra-fine grinding.
•
Larger Hopper Capacity than Competitive Models -
Reduces labor costs with less frequent refills.
•
Positive Flow Auger -
For uninterrupted coffee
dispensing.
•
Self-Adjusting Brew Rails -
Easily handle large Gemini
brew baskets.
•
Wide Match Profile -
Brew rails never extend beyond
housing with larger baskets.
•
Large Grinding Burrs -
Provide faster more efficient
operation.
•
Accurate and Consistent Throw -
For even distribution,
chaff reduction.
•
Uniform Grind
•
Powerful 1/2 hp Motor -
Equipped with safety circuit
breaker.
•
Standard 120VAC Operation
ILGD
INTERLOCK
CABLE
2.1
1.0
13.4
ELECTRICAL
CONNECTION
2.8
14.5
9.7
29.3
10.1
COFFEE
FRESH GROUND
SMALL
MEDIUM
LARGE
SMALL
MEDIUM
LARGE
ON/OFF
˝
˝
˝
˝
˝
˝
˝
˝
WILBUR CURTIS COMPANY, INC.
6913 Acco Street, Montebello, CA 90640-5403
Telephone: 800-421-6150 · 323-837-2300
Fax: 323-837-2406
www.wilburcurtis.com
SPECIFICATIONS
ILGD
Grind Cycles (Per Side)
3 per side
Hopper Capacity (Whole Beans)
7.5 lbs ea. side
Timer
Digital InterLock
Portion Range
1 to 99 Seconds
Dimensions (H x W x D)
29.3” x 10.1” x 14.5”
Voltage
120VAC/60Hz
Power Requirements
8.0A
Motor
1/2 hp
Shipping Weight (lbs.)
60 lbs.
Cube (cu. ft.)
4.6 cu. ft.
FACTORY SETTINGS
ILGD GRINDER
Volume/Grind Setting
Large - 15 sec.
Medium - 10 sec.
Small - 5 sec.