Whistler 1765 Manuale Utente
INSTALLATION
shield bracket. Press the bracket release button and re m o v e
the detector before bending.
the detector before bending.
Dash Mounting
• Make sure the mounting location you have chosen is
relatively level and is clean and dry. Clean with isopro p y l
alcohol if necessary to remove any waxes or polishes.
• Separate the fastener strips. Peel the paper backing off
each strip and adhere one piece to the dash and the other
piece to the bottom of the unit, taking care not to cover
the serial number.
• Make sure the mounting location you have chosen is
relatively level and is clean and dry. Clean with isopro p y l
alcohol if necessary to remove any waxes or polishes.
• Separate the fastener strips. Peel the paper backing off
each strip and adhere one piece to the dash and the other
piece to the bottom of the unit, taking care not to cover
the serial number.
Be careful not to place the fastener strip over the unit’s serial number. If the
fastener strip is removed, the serial number may be pulled off the unit. Units
without serial numbers are not covered under warr a n t y.
fastener strip is removed, the serial number may be pulled off the unit. Units
without serial numbers are not covered under warr a n t y.
7
INSTALLATION
Mounting Guidelines
• Mount the unit as low and level as possible near the center
of the windshield. Unit must be level for compass to function
p ro p e r l y. (Models 1760/1765 only)
• Do not mount your unit behind wipers, ornaments,
m i rro red sunscreens, etc. These obstructions have metal
s u rfaces which can affect radar and laser signals and re d u c e
critical warning time. (Regular tinted glass does not aff e c t
re c e p t i o n . )
• Some windshields have an Instaclear
• Mount the unit as low and level as possible near the center
of the windshield. Unit must be level for compass to function
p ro p e r l y. (Models 1760/1765 only)
• Do not mount your unit behind wipers, ornaments,
m i rro red sunscreens, etc. These obstructions have metal
s u rfaces which can affect radar and laser signals and re d u c e
critical warning time. (Regular tinted glass does not aff e c t
re c e p t i o n . )
• Some windshields have an Instaclear
™
or Electriclear
™
t y p e
coating, which affect radar signals. Consult your dealer or the
o w n e r’s manual supplied with your vehicle to determine if
your windshield has this coating.
• Avoid placing unit in direct contact with windshield.
• To reduce the possibility of theft, conceal your unit when
not in use.
o w n e r’s manual supplied with your vehicle to determine if
your windshield has this coating.
• Avoid placing unit in direct contact with windshield.
• To reduce the possibility of theft, conceal your unit when
not in use.
Windshield Mounting
• Install the two suction cups and rubber bumper onto the
bracket by fitting them into their holes.
• P ress the suction cups onto the windshield at the location
you have chosen. I M P O RTA N T: Some newer cars have a
plastic safety coating on the inside of the windshield. The
suction cups may leave permanent marks on this type of
s u rface. To find out if your vehicle has this type of
windshield, check the owner’s manual or ask your dealer.
We recommend that you do not leave the suction cup
bracket on the window in direct sunlight. If the detector
is removed, this may cause blistering of the dash in some
v e h i c l e s .
• Install the two suction cups and rubber bumper onto the
bracket by fitting them into their holes.
• P ress the suction cups onto the windshield at the location
you have chosen. I M P O RTA N T: Some newer cars have a
plastic safety coating on the inside of the windshield. The
suction cups may leave permanent marks on this type of
s u rface. To find out if your vehicle has this type of
windshield, check the owner’s manual or ask your dealer.
We recommend that you do not leave the suction cup
bracket on the window in direct sunlight. If the detector
is removed, this may cause blistering of the dash in some
v e h i c l e s .
• Slide the detector onto the bracket until it locks into place.
• If necessary, the unit may be leveled by bending the wind-
• If necessary, the unit may be leveled by bending the wind-
6
1750/1760/1765 manual 3/6/02 2:20 PM Page 9