Westinghouse Wensley Two-Light Semi-Flush Ceiling Fixture 6622300 Manuale Istruttivo

W-392

061814

Line art shown may not exactly match the 

fixture enclosed. However, the installation 

instructions do apply to this fixture.

Il est possible que le dessin illustré ici ne 

soit pas la reproduction exacte de l’appareil 

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent 

cependant valables.

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a 

period of Five Years from purchase date.  This warranty is in lieu of all other warranties expressed or 

implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration 

of components, nor does it cover damages caused through abuse, improper installation, surges in 

electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.

Congratulations on your Westinghouse purchase.  This fixture has been designed to give you many 

years of beauty and service.  For questions and comments, please visit www.westinghouselighting.

com/contact-us.
NOTE: Carefully unpack fixture and parts.  Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de matéri-

aux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se substitue 

à toute autre garantie expresse ou tacite.

 

Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la 

foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages 

survenant suite à une utilisation anormale, une installation impropre, une surtension de courant élec-

trique ou des actes d’un tiers.

 

Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez- 

nous gratuitement au numéro suivant : 1-888-417-6222.

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été 

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces 

y sont avant de mettre l’emballage au rebut (voir fig. 1).

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires.  These fixtures 

meet all UL specifications.
1.      Turn off power at circuit box to avoid possible electric shock.

2.   Thread mounting screws (A) into mounting bar (B) (see fig. 1).

3.   Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).

4.   Spread fixture arms (E) to an equal distance apart (if applicable).

5.   Identify color coding of fixture wires (see fig. 2).

6.   To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet 

      box wire. Do not twist wires.

7.   Fit wire connector (F from figure 1) over wires and twist until there is a firm connection. If wire 

      connector (F) easily comes off, reattach and check again for a firm connection.

8.   Repeat steps 5, 6 and 7 with the white (group B from fig. 2) fixture wires and outlet box wires.

9.   Partially thread green grounding screw (G) into side hole (H) on mounting plate (B) (see fig. 1).

10. Wrap ground wire from fixture around green grounding screw (G) leaving enough excess wire, 

      then connect ground wire and outlet box wire with wire connector (F) (if applicable).

11. Tighten green grounding screw (G). Do not over tighten.

12. Tuck wires inside outlet box (C) (see fig. 1).

  Warning: This fixture is for indoor use only.
1.   Place canopy (I) over mounting screws (A), with mounting screws (A) protruding through openings 

      in canopy (I), and secure with cap nuts (J) (see fig. 1).

2.   Thread hex nut 1 (K1) onto nipple (L) then thread nipple (L) into coupling (M) and secure hex nut 1 

      (K1).

3.   Place nipple cover (N) over nipple (L) and secure with cover cap (O) and hex nut 2 (K2) or rubber 

      washer (if applicable).

4.   Install lamps. Do not exceed recommended wattage.

5.   Place fixture ring (Q) on top of glass shade (P), if applicable.

6.   Raise glass shade (P) and fixture ring (Q), if applicable, so that nipple (L) protrudes through the 

      opening in glass shade (P) and secure with washer (R) and hex nut 3 (K3).

7.   Place decorative cap (S) over nipple (L) and secure with finial (T).

8.   Turn power back on at circuit box.

CLEANING AND CARE 

To clean, wipe fixture with soft cloth.  Clean glass with mild soap.  Spray from chemical cleaners can 

discolor the finish of fixture.  Extend-A-Finish Laquer Conditioner, Item#70295, is recommended once 

a year to clean, condition, and protect fixture.  Do not use scouring pads, powders, steel wool or abra-

sive paper to clean this fixture.
NOTE  FOR FIXTURES THAT ARE  SOLID BRASS:

Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-

quer which gives maximum protection against the weather.  However, in time the brightness of the 

brass will tarnish, giving way to an authentic old-world brass finish.  To keep your solid brass fixture 

looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-

faces, giving the fixture an extra protective covering.

ORDERING PARTS 

Keep this manual for future reference, and in case replacement parts are needed.  Available parts can 

be ordered from place of purchase.  Use exact wording from diagrams when ordering parts.

CONNECT TO BLACK

HOUSE WIRE

BLACK

WHITE OR GREY WITH TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

WHITE

WHITE OR GREY WITHOUT TRACER

CONNECT TO WHITE

HOUSE WIRE

NOTE: When parallel wire (SPT 1 & SPT 2) is used; the neutral wire is square shaped

and ridged, and the hot wire will be round in shape and smooth. (See below.)

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.  

www.westinghouselighting.com

       , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.           
Used under licensee by Westinghouse Lighting. 

All rights reserved. 

 

Made in China