Westinghouse Three-Light Indoor Bath Bar 6640600 Manuale Istruttivo

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires.  These fixtures 

meet all UL specifications.
1.      Turn off power at circuit box to avoid possible electric shock.

2.   Beginning at sides and working at an angle, peel protective coating (if applicable) from face plate 

      (A) (see fig. 1).

3.   Remove cups (B) from sockets (C) by simultaneously twisting and pulling cups (B) counter 

      clockwise off of sockets (C). If fixture is supplied with rings (R), unscrew counter clockwise off of 

      sockets (C).

4.   Remove screws (D) and lock washers (E) (if applicable) from outer edges of face plate (A).

5.   Separate decorative plate (F) (if applicable) and face plate (A) from back plate (G).

6.   Push wires through back plate opening (H).

7.   Identify color coding of fixtures (see fig. 2).

8.   To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet 

      box wire. Do not twist wires.

9.   Fit wire connector (I) over wires and twist until there is a firm connection. If wire

      connector (I) easily comes off, reattach and check again for a firm connection.

10. Repeat steps 8 and 9 with the white (group B from fig. 2) fixture wires and outlet box wires.

11. Partially thread green grounding screw (J) into side hole (K) on back plate (G) (see fig. 1).

12. Wrap ground wire from fixture around green grounding screw (J) leaving enough excess wire, 

      then connect ground wire and outlet box wire with wire connector (I) (if applicable).

13. Tighten green grounding screw (J). Do not over tighten.

14. Tuck wires inside outlet box (L).

  Warning: This fixture is for indoor use only.
NOTE: For maximum support, secure back plate (G) with wood screws (M) (or plastic anchors

(N)) if outer holes (P) meet sheetrock by following steps 1 and 2 below.
1.   Position flat side of back plate (G) against wall at mounting location and mark outer holes (P) with 

      a pencil.

      NOTE: Back plate (G) must be level for fixture to hang straight.

2.   Drill a 1/8” hole at each mark then insert plastic anchors (N) by gently tapping with a hammer.

3.   Place back plate (G) over outlet box (L) and secure using outlet box screws (Q) (if applicable), and 

      wood screws (M) (vertically or horizontally as desired, see fig. 1).

4.   Position face plate (A) then decorative plate (F) (if applicable) over back plate (G) and sockets (C).

5.   Secure by simultaneously twisting and pushing cups (B) clockwise over sockets (C) (for a tighter fit, 

      slightly bend tabs inside cups (B) outward).

      NOTE: If fixture is supplied with threaded sockets (C), thread rings (R) onto sockets (C).

6.   Replace screws (D) (if applicable) and lock washers (E) (if applicable) on outer edges of face plate (A).

7.   Install lamp(s). Do not exceed recommended wattage.

8.   Turn power back on at circuit box.

W-386

052814

CLEANING AND CARE 

To clean, wipe fixture with soft cloth.  Clean glass with mild soap.  Spray from chemical cleaners can discolor the 

finish of fixture.  Extend-A-Finish Laquer Conditioner, Item#70295, is recommended once a year to clean, condi-

tion, and protect fixture.  Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
NOTE  FOR FIXTURES THAT ARE  SOLID BRASS:

Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lacquer which 

gives maximum protection against the weather.  However, in time the brightness of the brass will tarnish, giv-

ing way to an authentic old-world brass finish.  To keep your solid brass fixture looking new for years to come, 

regularly apply a good quality, non-abrasive car wax to all metal surfaces, giving the fixture an extra protective 

covering.

ORDERING PARTS 

Keep this manual for future reference, and in case replacement parts are needed.  Available parts can be ordered 

from place of purchase.  Use exact wording from diagrams when ordering parts.

CONNECT TO BLACK

HOUSE WIRE

BLACK

WHITE OR GREY WITH TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

WHITE

WHITE OR GREY WITHOUT TRACER

CONNECT TO WHITE

HOUSE WIRE

NOTE: When parallel wire (SPT 1 & SPT 2) is used; the neutral wire is square shaped

and ridged, and the hot wire will be round in shape and smooth. (See below.)

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a 

period of Five Years from purchase date.  This warranty is in lieu of all other warranties expressed or 

implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration 

of components, nor does it cover damages caused through abuse, improper installation, surges in 

electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of the 

original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or replace 

the fixture or refund the purchase price.

Congratulations on your Westinghouse purchase.  This fixture has been designed to give you many 

years of beauty and service.  For questions and comments, please visit www.westinghouselighting.

com/contact-us.
NOTE: Carefully unpack fixture and parts.  Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de matéri-

aux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se substitue à 

toute autre garantie expresse ou tacite.

 

Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la 

foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages sur-

venant suite à une utilisation anormale, une installation impropre, une surtension de courant électrique 

ou des actes d’un tiers.

 

Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si cet appareil d’éclairage ne fonctionne pas pour une des raisons couvertes par la présente garantie, 

renvoyez tout simplement l’appareil d’éclairage et une copie de la preuve d’achat originale, frais de 

transport prépayés, à Westinghouse Lighting qui, à sa discrétion, réparera ou remplacera l’appareil ou 

vous remboursera le montant du prix d’achat.

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été 

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces y 

sont avant de mettre l’emballage au rebut (voir fig. 1).

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.  

www.westinghouselighting.com

       , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.           
Used under licensee by Westinghouse Lighting. 

All rights reserved. 

 

Made in China        

Il est possible que le dessin illustré ici ne 

soit pas la reproduction exacte de l’appareil 

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent 

cependant valables.

Line art shown may not exactly match the 

fixture enclosed. However, the installation 

instructions do apply to this fixture.