Westinghouse Parker Mews One-Light Indoor Flush Ceiling Fixture 6225800 Manuale Istruttivo
4
MOUNTING AND WIRING INSTRUCTIONS
MOUNTING AND WIRING INSTRUCTIONS
FIXTURE ASSEMBLY INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These
fixtures meet all UL specifications.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) (see fig. 1).
3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (not included).
4. Identify color coding of fixture wires (see fig. 2).
5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) (see fig. 1).
3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (not included).
4. Identify color coding of fixture wires (see fig. 2).
5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against
black outlet box wire. Do not twist wires.
6. Fit wire connector (E from fig. 1) over wires and twist until there is a firm connection. If
6. Fit wire connector (E from fig. 1) over wires and twist until there is a firm connection. If
wire connector (E) easily comes off, reattach and check again for a firm connection.
7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wires and outlet box wires.
8. Partially thread green grounding screw (F) into side hole (G) on mounting bar (B) (see fig. 1).
9. Wrap ground wire from fixture around green grounding screw (F) leaving enough excess
7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wires and outlet box wires.
8. Partially thread green grounding screw (F) into side hole (G) on mounting bar (B) (see fig. 1).
9. Wrap ground wire from fixture around green grounding screw (F) leaving enough excess
wire to then connect ground wire and outlet box wire with wire connector (E), if applicable.
10. Tighten green grounding screw (F). Do not over tighten.
11. Tuck wires inside outlet box (C).
10. Tighten green grounding screw (F). Do not over tighten.
11. Tuck wires inside outlet box (C).
Warning: This fixture is for indoor use only.
1. Raise canopy (H) to ceiling allowing mounting screws (A) to protrude through key slots (I)
1. Raise canopy (H) to ceiling allowing mounting screws (A) to protrude through key slots (I)
in canopy (H) (see fig. 1).
2. Rotate canopy (H) until mounting screws (A) lock into narrow end of key slots (I).
3. Install lamps. Do not exceed recommended wattage.
4. Thread hex nut (T) onto nipple (K), then thread nipple (K) into coupling (S).
2. Rotate canopy (H) until mounting screws (A) lock into narrow end of key slots (I).
3. Install lamps. Do not exceed recommended wattage.
4. Thread hex nut (T) onto nipple (K), then thread nipple (K) into coupling (S).
5. Slide flat washer (Q) and rubber washer (P) over nipple (K). Raise glass (J) up to
shade (R), with nipple (K) protruding through opening in glass (J),
6. Carefully support glass (J) while securing washer (L), hex nut (O), cap (M),
6. Carefully support glass (J) while securing washer (L), hex nut (O), cap (M),
and finial (N) to nipple (K).
7. Turn power back on at circuit box.
7. Turn power back on at circuit box.