Westinghouse Fallon Two-Light Indoor Semi-Flush Ceiling Fixture 6228700 Manuale Istruttivo

  NOTE: The above diagram illustrates the installa tion of your new lighting  
  fixture. This is a representative drawing and is not intended to match the  
  style of your fixture.

Fig 1

Fig 1A

NUT

RUBBER  PAD

Fig 2

Fig 2A

Fig 3

Fig 3A

NOTE: FIRST TURN OFF ELECTRICITY ADJUST THE CROSS BAR
1. If you are replacing an existing fixture, disconnect and remove the old fixture. Expose the supply wiring from the outlet box.
2. Some fixtures are provided with a threaded nipple (see Fig.1) or machine screws (see Fig. 2 and 2A) for attaching the fixture to the mounting bracket. If your  
     fixture is supplied with a threaded nipple, screw the nipple 3 complete turns into the mounting bracket and lock into place with a hexagon lock nut. If your 
     fixture is supplied with machine screws, thread the machine screws into the opposite side of the mounting bracket from the green ground screw. Lock the 
     machine screws into place with lock nuts. EXCEPTION: Ceiling mounted fixtures with keyhole slots should have machine screws entering mounting bracket 
     from same side as green grounding screw (see Fig.2A)
3. Fasten the mounting bracket to the outlet box using the two screws supplied with the outlet box. If your fixture is supplied with a channel shape mounting 
     bracket with keyhole slots for attachment to the mounting surface (see Fig.3), it will be necessary to mark the location of the keyhole slots on the mounting 
     surface and drill holes for fasteners (not provided). Use fasteners suitable for the mounting surface. The narrow end of the keyhole slot should face up.
4. Attach grounding wire (green or bare copper) from the supply circuit to the mounting bracket with the green grounding attachment screw provided. Some 
     models have a grounding wire attached to the fixture for models that employ a green or bare copper grounding wire, it will be necessary to connect the green 
     or bare grounding wire to the grounding conductor to the supply circuit. Attach all grounding conductors to the mounting bracket with the green grounding 
     attachment screw.
5. Make electrical connections-SEE BELOW.

To make electrical connections:
Connect the white wire(s) from the fixture to the white wire of the supply circuit. Connect the black wire(s) from the fixture to the black wire of the supply circuit. 
Connect the green (or bare copper) colored wire to the grounding conductor of the supply circuit. If your fixture is supplied with an SPT Cord connect the half 
of the SPT Cord that is ribbed surface to the white wire of the supply circuit. Connect the smooth half of the wire (the half with markings) to the black wire of the 
supply circuit. Use UL. Listed wire connectors suitable for the size, type, and number of conductors. No loose strands or loose wires should be present. Secure wire 
connectors with U.L. listed electrical tape.

1.  Spread the electrical splices so that the black wires are on one side of the outlet box and the white wires are on the other side.
2.  Place fixture against mounting surface allowing the threaded nipple or machine screws to pass through the coverplate. Secure with mounting nut or acorn 
     nuts. For fixtures with channel shape mounting bracket. Place the coverplate over the channel and secure with screws provided.
3.  If applicable place candle cover(s) over lampholder(s) before installing bulb(s). Install the light bulb(s) (not provided). CAUTION: Refer to the relamping label 
     located near the lampholder for recommended maximum wattage - do not exceed recommended wattage.
4.  If applicable, attach the shade to the fixture some shades require the use of shade attachment screws. Do not overtighten these screws – too much pressure 
     could cause glass brackage. See Fig.3 for placement of fabric spacer, not supplied on all models.
5.  Outdoor wall fixtures must be caulked with suitable RTV or Silicone compound around the top and sides of the coverplate to reduce the chance of water 
     intruding into the splicing area. Leave the bottom clear to allow moisture a means of escape.
6.  Restore electricity and check the operation of your new lighting fixture.

1.  To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.
2.  All electrical connections must be in accordance with local codes, ordinances, or the National Code. If your are unfamiliar with methods of installing electrical 
     wiring, secure the services of a qualified licensed electrician.
3.  These fixtures are intended to be mounted to a 4”X 2 1/8” deep metal octagon outlet box. The box must be directly supported by the building structure.
4.  Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. Turning the power off using the 
     light switch is not sufficient to prevent electrical shock.
NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be 
understood that common sense, caution and care are factors which cannot be built into any product. These factors must be supplied by the person(s) caring for and 
operating the fixture.

CAUTION: Before assembling your lighting fixture, refer to the section titled ELECTRICAL CONNECTIONS. If you feel you do not have electrical wiring experience, 
refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.

Blade screw driver
Adjustable wrench
Step Ladder
Wire cutters
Wiring supplies as required by electrical code

Check the contents of the box. You should receive:
     Mounting hardware package
     Lampholder assembly(s)
     Mounting bracket
     Shade(s)-not provided on all models
     Shade attachment screws (3 for each shade)-not provided on all models

W-354

051710