Vanguard Heating VMH26TNC Manuale Utente
www.desatech.com
113111-01A
10
LOCATING FIREPLACE
WARNING: Maintain the
minimum clearances shown in
Figures 6 and 7. If you can, pro-
vide greater clearances from
floor, ceiling, and joining wall.
Figures 6 and 7. If you can, pro-
vide greater clearances from
floor, ceiling, and joining wall.
You can recess firebox into the wall. You can also
position fireplace in the optional cabinet or cor-
ner mantels.
position fireplace in the optional cabinet or cor-
ner mantels.
IMPORTANT:
Only use optional
cabinet or corner mantels specified in this manual.
Purchase the optional mantel from your dealer (see
Accessories, page 30).
Purchase the optional mantel from your dealer (see
Accessories, page 30).
INSTALLATION
Continued
Figure 7 - Mounting Clearances As
Viewed From Front of Fireplace Shown
with Optional Mantel
Top Of
Mantel Can
Be Flush
With Wall
Mantel Can
Be Flush
With Wall
Left
Side
Side
CEILING
Right
Side
Side
36"
Minimum
Minimum
6"
Minimum
From
Sides Of
Fireplace
From
Sides Of
Fireplace
Left
Side
Side
CEILING
36"
Minimum
Minimum
FLOOR
Right
Side
Side
0" Minimum
To Top
Surface Of
Carpeting,
Tile Or Other
Combustible
Material
To Top
Surface Of
Carpeting,
Tile Or Other
Combustible
Material
0" Minimum
To Top
Surface Of
Carpeting,
Tile Or Other
Combustible
Material
To Top
Surface Of
Carpeting,
Tile Or Other
Combustible
Material
Figure 6 - Mounting Clearances As
Viewed From Front of Fireplace Shown
Built-In the Wall
Note:
When installing fireplace directly on car-
peting, tile or other combustible material, other
than wood flooring, the fireplace shall be installed
on a metal or wood panel extending the full width
and depth of the fireplace.
than wood flooring, the fireplace shall be installed
on a metal or wood panel extending the full width
and depth of the fireplace.
CAUTION: If you install the
fireplace in a home garage
• fireplace pilot and burner must
• fireplace pilot and burner must
be at least 18 inches above floor.
• locate fireplace where moving
vehicle will not hit it.
For convenience and efficiency, install fireplace
• where there is easy access for operation, inspec-
tion, and service.
• in coldest part of room.
An optional blower kit is available from your dealer
(see Accessories, page 30). If planning to use
blower, locate fireplace near an electrical outlet.
(see Accessories, page 30). If planning to use
blower, locate fireplace near an electrical outlet.
BUILT-IN FIREPLACE
INSTALLATION
INSTALLATION
Built-in installation of this fireplace involves in-
stalling fireplace into a framed-in enclosure. This
makes the front of fireplace flush with wall. An
optional trim kit accessory is available (see Ac-
cessories, page 30). Trim will extend past sides of
fireplace approximately 1/2 inch. This will cover
the rough edges of the wall opening. If installing
a built-in mantel above the fireplace you must fol-
low the clearances shown in Figure 11, page 12.
Follow the instructions below to install the fire-
place in this manner.
stalling fireplace into a framed-in enclosure. This
makes the front of fireplace flush with wall. An
optional trim kit accessory is available (see Ac-
cessories, page 30). Trim will extend past sides of
fireplace approximately 1/2 inch. This will cover
the rough edges of the wall opening. If installing
a built-in mantel above the fireplace you must fol-
low the clearances shown in Figure 11, page 12.
Follow the instructions below to install the fire-
place in this manner.
Actual
Framing
Height
26"
26
7
/
8
"
Front Width
26
3
/
4
"
26
7
/
8
"
Depth
9
1
/
2
"
10
1
/
2
"
Bottom
3/4"
3/4"
1.
Frame in rough opening. Use dimensions
shown in Figure 8, page 11, for the rough
opening.
shown in Figure 8, page 11, for the rough
opening.
If installing in a corner, use dimensions shown
in Figure 9, page 11, for the rough opening.
The height is 26
in Figure 9, page 11, for the rough opening.
The height is 26
7
/
8
" which is the same as the
wall opening above.