Interfire Audio IFC-525 Dépliant
COMPONENT WOOFER INSTALLATION INSTRUCTION MANUAL
MOUNTING LOCATION
Carefully select a suitable mounting location for the speaker/tweeter. Be sure to check
behind the mounting location selected for adequate space for speaker/tweeter depth.
Use the included template if needed
behind the mounting location selected for adequate space for speaker/tweeter depth.
Use the included template if needed
MOUNTING HOLE
SPEAKER : Using a sharp knife or razor, cut the panel using the outline from the template as a guide. Also,
drill holes for the mounting screws if installing on metal panels.
drill holes for the mounting screws if installing on metal panels.
INSTALLATION
SPEAKER : Place ABS grill on top of speaker and secure assembly using the self tapping
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.
TWEETER : Screw the angle mounting to the location selected or use the double sided
tape provided to stick the flush mounting to the location selected.
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.
TWEETER : Screw the angle mounting to the location selected or use the double sided
tape provided to stick the flush mounting to the location selected.
WIRING
INSTALLATION PROCEDURE :
Speaker
Tweeter
Inter fire Audio Inc.
Santa Fe Springs, CA,
www.inter fireaudio.com
SPEAKER: Carefully route the supplied wire to the speaker, ensuring that it does not pass over any sharp
metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers,
watching that the left/right and positive/negative connections are made correctly to the appropriate
outputs of the radio or amplifier.
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening
and connect these wires to the line wires coming from the included outboard crossover tweeter
terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.
metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers,
watching that the left/right and positive/negative connections are made correctly to the appropriate
outputs of the radio or amplifier.
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening
and connect these wires to the line wires coming from the included outboard crossover tweeter
terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.
Mounting Holes
Speaker Unit
Mounting Screws
Grill
Tweeter
Screw
Angle Mounting
Double sided
Tape
Tape
Flush Mounting
Peak Power Handling
Continuous Power (RMS)
Impedance
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
Crossover
Continuous Power (RMS)
Impedance
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
Crossover
: 300Watts
: 150 Watts
: 4 Ohm
: 10 Oz
: 91 dB
: 50Hz - 25kHz
: 1" (25mm) ASV
: 92.06 Hz
: 0.82
: 4.1 Lt
: 12dB/Oct
: 150 Watts
: 4 Ohm
: 10 Oz
: 91 dB
: 50Hz - 25kHz
: 1" (25mm) ASV
: 92.06 Hz
: 0.82
: 4.1 Lt
: 12dB/Oct
MODEL : IFC-525
5.25" 2-Way High Definition
Component System
5.25" Injection PP Mica Cone
Rubber Surround and
1" Titanium Dome Tweeter
with Neodymium Magnet
Peak Power Handling
Continuous Power (RMS)
Impedance
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
Crossover
Continuous Power (RMS)
Impedance
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
Crossover
: 350Watts
: 175 Watts
: 4 Ohm
: 13 Oz
: 91 dB
: 40Hz - 25kHz
: 1" (25mm) ASV
: 53.1 Hz
: 0.61
: 12.42 Lt
: 12dB/Oct
: 175 Watts
: 4 Ohm
: 13 Oz
: 91 dB
: 40Hz - 25kHz
: 1" (25mm) ASV
: 53.1 Hz
: 0.61
: 12.42 Lt
: 12dB/Oct
MODEL : IFC-650
6.5" 2-Way High Definition
Component System
6.5" Injection PP Mica Cone
Rubber Surround and
1" Titanium Dome Tweeter
with Neodymium Magnet
SPECIFICATIONS :
COMPONENT WIRING DIAGRAM:
INPUT
WOOFER
SIGNAL SOURCE UNIT
RADIO OR AMPLIFIER
TWEETER
EXTERNAL 2-WAY
CROSSOVER
*NOTE : When installing tweeter with flush mount kit, a hot glue gun is sometimes necessary to secure
the tweeter's flush mount housing.
the tweeter's flush mount housing.