Chauvet Home Safety Product color ado1ip Manuale Utente
Setup
-6-
COLORado™ 1 IP User Manual Rev. 01c
3. Setup
AC Power
The COLORado™ 1 IP has an auto-ranging power supply that can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
voltage range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual, or on the product’s sticker.
specifications in this guide, the product’s user manual, or on the product’s sticker.
Always connect the COLORado™ 1 IP to a protected circuit with an appropriate
electrical ground to avoid the risk of electrocution or fire.
electrical ground to avoid the risk of electrocution or fire.
To determine the power requirements for the COLORado™ 1 IP see the label affixed to
the side of the fixture. Alternatively, you may refer to the corresponding specifications
chart in the Technical Information chapter of this manual.
the side of the fixture. Alternatively, you may refer to the corresponding specifications
chart in the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
For more information, you may download the “Sizing the Circuit Breakers” document
from the CHAUVET® Web site.
Never connect the COLORado™ 1 IP to a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
Each COLORado™ 1 IP has IP66 rated cords for Power In and Power Out with
proprietary IP66 connectors. These power cords access the sealed body of the fixture
through IP66 cable glands. To allow connection to power outlets, the fixture comes with
a power input cord with a proprietary IP66 connector on one end and an Edison plug on
the other end (US market). In case you need to replace the Edison plug on the power
input cord, follow the table below.
proprietary IP66 connectors. These power cords access the sealed body of the fixture
through IP66 cable glands. To allow connection to power outlets, the fixture comes with
a power input cord with a proprietary IP66 connector on one end and an Edison plug on
the other end (US market). In case you need to replace the Edison plug on the power
input cord, follow the table below.
Connection
Wire (US)
Wire (Europe)
IP66 Pin
Screw Color
AC Live
Black
Brown
1
Yellow or Brass
AC Neutral
White
Blue
2
Silver
AC Ground
Green/Yellow
Green/Yellow
3
Green
Power Linking
The COLORado™ 1 IP supports power linking for up to 12 other COLORado™ 1 IP
fixtures at 120 VAC. The fixture also comes with an IP66 power linking cord to allow
direct connection between fixtures.
fixtures at 120 VAC. The fixture also comes with an IP66 power linking cord to allow
direct connection between fixtures.
Fuse Replacement
The COLORado™ 1 IP fixture has no external fuse that the user can change. However,
it does have an internal fuse that only an authorized CHAUVET® technician should
change.
it does have an internal fuse that only an authorized CHAUVET® technician should
change.
DMX Linking
You may link any COLORado™ 1 IP fixture to a DMX controller using a standard DMX
serial connection. If using other DMX compatible fixtures with a COLORado™ 1 IP
fixture, it is possible to control them individually with a single DMX controller.
serial connection. If using other DMX compatible fixtures with a COLORado™ 1 IP
fixture, it is possible to control them individually with a single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the COLORado™ 1 IP fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
cables needed to link the COLORado™ 1 IP fixture to a DMX controller, you may
download the “DMX Primer” document from the CHAUVET® Web site.
The COLORado™ 1 IP comes with two adapter cables, one from proprietary IP66
to 3-pin DMX In and the other from proprietary IP66 to 3-pin DMX Out. In addition,
it comes with a signal linking cable with proprietary IP66 connectors on both
ends.
to 3-pin DMX In and the other from proprietary IP66 to 3-pin DMX Out. In addition,
it comes with a signal linking cable with proprietary IP66 connectors on both
ends.
DMX Modes
The COLORado™ 1 IP uses the standard DMX data connection for its DMX modes,
TOUR, ARC1, AR1 + D, ARC2, AR2 + D, AR2 + S, and HSV.
TOUR, ARC1, AR1 + D, ARC2, AR2 + D, AR2 + S, and HSV.
You will find information about these DMX modes in the Introduction chapter (brief
description), the Operation Instructions chapter (configuration details), and the DMX
Values section (individual channel values).
description), the Operation Instructions chapter (configuration details), and the DMX
Values section (individual channel values).