Cambridge Audio AZUR 550T Manuale Utente
6
Tuning and listening to the 550T
1. Press the Standby/On button on the front panel.
2. Select FM or AM by pushing the FM/AM button on front panel or remote
control.
3. Press the
buttons to manually select the desired frequency, or
hold either button down to search for a station.
Setting presets
Select the station you wish to store. Press and hold the Mode/Store
button, then use
button, then use
to select the slot where the station will be stored.
Press Mode/Store again to save it.
How to select preset stations
1. Press the Standby/On button on the front panel.
2. Select FM or AM by pushing the FM/AM button on front panel or remote
control.
3. Press chosen preset button to listen to the corresponding station.
Alternatively, press the Mode/Store button to enable Preset mode, then
use the
use the
buttons to cycle through the stored stations.
Setting the clock
The user can either allow RDS transmissions to automatically set the
Clock Time/Date, or the Clock can be set manually. To change the Clock
mode, press and hold the Clock button on the remote control. Use the
Clock Time/Date, or the Clock can be set manually. To change the Clock
mode, press and hold the Clock button on the remote control. Use the
buttons on the remote to change mode between RDS and Manual.
Press the Alarm button again to confirm your choice. If Manual mode is
selected, you can then set the time. Firstly, adjust the hour using the
Press the Alarm button again to confirm your choice. If Manual mode is
selected, you can then set the time. Firstly, adjust the hour using the
buttons. When that is done, press Clock again to adjust the minutes.
Press Clock again to finish.
Press Clock again to finish.
Setting the alarm time
The Alarm function will turn on the 550T at a chosen time. It will also
generate a command on the control bus that, when connected, will turn
on a Cambridge Audio Azur series amplifier and select the tuner input.
generate a command on the control bus that, when connected, will turn
on a Cambridge Audio Azur series amplifier and select the tuner input.
To set the Alarm time:
1. Press Alarm/Clock on your remote handset.
2. Use
buttons to select if the alarm should be off, just work once,
or every day.
3. Press Clock.
4. Press
keys to alter the hour
5. Press Clock.
6. Press
keys to alter the minute
7. Press Clock to finish.
Setting the sleep time
The Sleep function will turn off the 550T at a chosen time. It will also
generate a command on the Control Bus that, when connected, will turn
off a compatible Cambridge Audio Azur series amplifier.
generate a command on the Control Bus that, when connected, will turn
off a compatible Cambridge Audio Azur series amplifier.
To set the Sleep time:
1. Press and hold Alarm/Clock and then press Standby on your remote
handset.
2. Press the
keys to alter the hour
3. Press Clock.
4. Press the
keys to alter the minute
5. Press Clock to finish.
Connecting the Control Bus
If it is desired to control a Cambridge Audio Azur amplifier by the 550T’s
Alarm or Sleep timers, connect the two units via the orange Control Bus
sockets using the supplied orange RCA/phono lead as shown below:
Alarm or Sleep timers, connect the two units via the orange Control Bus
sockets using the supplied orange RCA/phono lead as shown below:
Custom installation (C.I.) use
The 550T features a Control Bus input/output that allow un-modulated
remote control commands (positive logic, TTL level) to be received
electrically by the unit and looped to another unit if desired. These control
commands are typically generated by custom installation (multi-room)
systems or remote IR receiver systems. The Control Bus sockets are
colour-coded orange.
remote control commands (positive logic, TTL level) to be received
electrically by the unit and looped to another unit if desired. These control
commands are typically generated by custom installation (multi-room)
systems or remote IR receiver systems. The Control Bus sockets are
colour-coded orange.
An IR Emitter Input is also provided that allows modulated IR remote
control commands to be received electrically by the unit. Commands on
this input operate the unit only and are not looped out demodulated on
the Control Bus Output.
control commands to be received electrically by the unit. Commands on
this input operate the unit only and are not looped out demodulated on
the Control Bus Output.
In addition the unit features direct IR/Control codes as well as toggle
codes for many of its features to simplify programming custom installation
systems. Special direct commands can be accessed on the supplied
remote control for teaching into C.I. systems as follows:
codes for many of its features to simplify programming custom installation
systems. Special direct commands can be accessed on the supplied
remote control for teaching into C.I. systems as follows:
Specific power on/off commands – press and hold the Standby button.
The remote first generates it's usual amp and tuner standby (toggle)
commands (both are sent). Keep the button held down, after 12 seconds
an Amp On command will be generated, then if the button is kept held
down after a further 12 seconds an Amp off command is generated, then
separated by 12 second pauses, Tuner On, and finally Tuner Off.
The remote first generates it's usual amp and tuner standby (toggle)
commands (both are sent). Keep the button held down, after 12 seconds
an Amp On command will be generated, then if the button is kept held
down after a further 12 seconds an Amp off command is generated, then
separated by 12 second pauses, Tuner On, and finally Tuner Off.
Specific band selection commands – press and hold the FM/AM key. The
usual band toggle command is first, then the FM Mode command,
followed by the AM Mode command is generated.
usual band toggle command is first, then the FM Mode command,
followed by the AM Mode command is generated.
Specific Preset/Scan mode commands – Press and hold the Mode key.
The usual mode toggle command is first, then the Scan Mode command,
followed by the Preset Mode command.
The usual mode toggle command is first, then the Scan Mode command,
followed by the Preset Mode command.
Specific Mute On/Off commands – press and hold the Mute key. The
usual mute toggle command is first, followed by the Mute On command,
and then the Mute Off command.
usual mute toggle command is first, followed by the Mute On command,
and then the Mute Off command.
A full code table for this product is available on the Cambridge Audio
website at www.cambridge-audio.com.
website at www.cambridge-audio.com.
Operating instructions
Caution
Serial Number Label Removed
Manufactured in an
ISO9001 approved facility
IR Emitter
In
Power Rating
: 220 - 230V AC ~ 50/60Hz
Max Power Consumption: 7W
87.50Mhz - 108.00Mhz FM
531Khz - 1602Khz AM
In
Out
Control Bus
Line Output
Line Output
Right
Right
Left
Left
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this
device does not cause harmful interference.
device does not cause harmful interference.
AM 300
Ω
FM 75
Ω
Designed and engineered in London, England
azur 550T FM/AM Tuner
www.cambridgeaudio.com
Made under licence in China
Apparatet må kun tilkoples jordet stikkontakt. Laite on liitettävä
suojamaadoituskoskoskettimilla varustenttuun pistorasiaan.
Apparaten skall anslutas till jordat uttagt.
550T
550A