Garmin 010-11099-10 Manuale Utente

To obtain the best performance and to avoid damage to your boat, 

install the Garmin

®

 2.1 L hydraulic pump according to the following 

instructions. These instructions are a supplement to the installation 

instructions provided with your Garmin autopilot.
Professional installation of the pump is highly recommended, because 

specific knowledge of hydraulic steering componentry is required to 

properly install the pump.
Read all installation instructions before proceeding with the 

installation. If you experience difficulty during the installation, contact 

Garmin Product Support.

Help us better support you by completing your online registration today.
•  Go to 

http://my.garmin.com

.

•  Keep the original sales receipt, or a photocopy, in a safe place.

Contact Garmin Product Support if you have any questions about this 

product.
•  In the USA, go to 

www.garmin.com/support

, or contact Garmin 

USA by phone at (913) 397.8200 or (800) 800.1200.

•  In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
•  In Europe, go to 

www.garmin.com/support

 and click Contact 

Support for in-country support.

‹

vessel. The autopilot is a tool that will enhance your capability to 

operate your boat. It does not relieve you from the responsiblility of 

safely operating your boat. Avoid navigational hazards and never leave 

the helm unattended.
See the Important Safety and Product Information guide in the autopilot 

product box for product warnings and other important information.

‹

Failure to install and maintain this equipment in accordance with these 

instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask when 

drilling, cutting, or sanding.

This equipment should be installed by a qualified marine installer.
This equipment is only for use with Garmin autopilots.
When drilling or cutting, always check the opposite side of the surface. 

Be aware of fuel tanks, electrical cables, and hydraulic hoses.

The 2.1 L hydraulic pump steers your boat by interacting with the 

hydraulic steering system, based on commands you enter using the 

autopilot display unit. The pump is not included in the autopilot core 

package box because the type of pump you use with your autopilot is 

determined by the size and type of steering system on your boat.

•  2.1 L pump kit (part number 010-11099-10)
•  Hydraulic hose with machine-crimpted or field-replaceable fittings 

that have a minimum rating of 1000 lbf/in

2

.

•  Inline hydraulic shut-off valves
•  Hydraulic fluid
•  Thread sealant
•  Hydraulic bleeding equipment
•  Mounting screws: mounting screws are provided in the pump kit, but 

if the provided screws are not appropriate for the mounting surface, 

you must provide the correct types of screws.

•  Safety glasses
•  Drill and drill bits
•  Wrenches
•  Wire cutter/strippers
•  Screwdrivers: Phillips and flat-head
•  Cable ties
•  Marine sealant
•  Marine corrosion inhibitor spray

Because every boat is different, care must be taken when planning the 

pump installation.
1.  Choose a mounting location (

).

2.  Mount the pump (

).

3.  Connect the pump to the hydraulic lines (

).

4.  Connect the pump to the autopilot ECU (

).

1.  Consult the diagrams on 

for connection and dimension 

considerations.

2.  Choose a location to install the pump, considering the following 

guidelines:
•  The pump must be located within 19 in. (0.5 m) of the ECU. 
•  The cables that connect the pump to the ECU cannot be 

extended.

•  The pump should be mounted horizontally, if possible. 
•  If the pump cannot be mounted pump horizontally, it must be 

mounted vertically with the pump head connectors facing up.

•  The pump must be mounted in a location to which you can 

extend the hydraulic steering lines of the boat.

•  The pump has five hydraulic-connector fittings, enabling 

illustration of the fitting layout and 

 to view an illustration 

of the alternate installation method.